2007-2013 Highlander Kluger · Service Manual BODY

Touch Sensor Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the power back door ECU receives a jam signal from the touch sensor while the power back door closer is operating, the ECU reverses the back door operation and opens the door.

WIRING DIAGRAM

B165200E06

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (POWER BACK DOOR TOUCH SENSOR)
  1. Check the Data List for proper functioning of the power back door touch sensor.

    Back door (Power back door ECU) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    PBD Touch Sen L
    Power back door touch sensor LH signal / ON or OFF
    ON: Power back door touch sensor is LH pressed
    OFF: Power back door touch sensor is LH not pressed
    -
    PBD Touch Sen R
    Power back door touch sensor RH signal / ON or OFF
    ON: Power back door touch sensor RH is pressed
    OFF: Power back door touch sensor RH is not pressed
    -

    OK:
    The display is as specified in the normal condition.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT POWER BACK DOOR TOUCH SENSOR

  1. B165213E01
    Remove the power back door touch sensor. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Not pressed
    Approx. 1 kΩ
    1 - 2
    Pressed
    Below 100 Ω



NG
REPLACE POWER BACK DOOR TOUCH SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR TOUCH SENSOR - POWER BACK DOOR DRIVE UNIT AND BODY GROUND)

  1. B165209E06
    LH Side
    1. Disconnect the T7 sensor connectors.

    2. Disconnect the O14 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      T7-1 (OSL) - O14-15 (OSL)
      Always
      Below 1 Ω
      T7-2 (OSLE) - O14-14 (OSE)
      Always
      Below 1 Ω
      T7-1 (OSL) - Body ground
      Always
      10 kΩ or higher
      T7-2 (OSLE) - Body ground
      Always
      Below 1 Ω

  1. B165209E07
    RH Side
    1. Disconnect the T8 sensor connectors.

    2. Disconnect the O14 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      T8-1 (OSR) - O14-13 (OSR)
      Always
      Below 1 Ω
      T8-2 (OSRE) - O14-14 (OSE)
      Always
      Below 1 Ω
      T8-1 (OSR) - Body ground
      Always
      10 kΩ or higher
      T8-2 (OSRE) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)


← Jam Protection Function Activates During Power Back Door Operation (from Jul 2010)Touch Sensor Circuit (Aug 2008 – Jun 2010) →