2007-2013 Highlander Kluger · Service Manual BRAKE

C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC)

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

DTC C1379 will be deleted when the downhill assist control switch sends a downhill assist control operation signal or when Test Mode ends. DTC C1379 is output only in Test Mode.
DTC Code
DTC Detection Condition
Trouble Area
C1379
Detected only during Test Mode.
Downhill assist control switch

WIRING DIAGRAM

C167504E01

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. READ VALUE ON INTELLIGENT TESTER (DOWNHILL ASSIST CONTROL SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Downhill Assist Control Switch
    Downhill assist control switch / ON or OFF
    ON: Switch ON
    OFF: Switch OFF
    -

  1. Using the intelligent tester, check the switch condition on the intelligent tester changes according to downhill assist control switch operation.

    OK:
    The intelligent tester displays ON or OFF according to downhill assist control switch operation.



NG
Go to step 3
OK


2. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

3. INSPECT DOWNHILL ASSIST CONTROL SWITCH

  1. C156507E01
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the downhill assist control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (B) - 1 (E)
    Switch is pushed in
    Below 1 Ω
    4 (B) - 1 (E)
    Switch is not pushed in
    10 kΩ or higher

    NOTICE:
    Check the downhill assist control switch signal after replacement (Click here).



NG
REPLACE DOWNHILL ASSIST CONTROL SWITCH (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DOWNHILL ASSIST CONTROL SWITCH)

  1. C168258E01
    Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-26 (HDCS) - g2-4 (B)
    Always
    Below 1 Ω
    A24-26 (HDCS) - Body ground
    Always
    10 kΩ or higher
    g2-1 (E) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC) (May 2007 – Jul 2008)C1379 Downhill Assist Control Switch Malfunction (Test Mode DTC) (from Jul 2010) →