2007-2013 Highlander Kluger · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

  1. C165374
    Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. C165373
    Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. C165371
    Connect the brake pedal load sensing switch connector and engage the clamp.


2. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

  1. C165376
    Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. C165375
    Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. C165372
    Connect the brake pedal load sensing switch connector and engage the clamp.


3. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS

  1. C166415E01
    Apply lithium soap base glycol grease to the push rod pin.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.


4. INSTALL BRAKE PEDAL RETURN SPRING

  1. C165369
    Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.


5. INSTALL STOP LIGHT SWITCH ASSEMBLY

  1. E150075E01
    Temporarily install the stop light switch assembly with the stop light switch lock nut.

  1. E150611E01
    Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).

  1. Tighten the stop light switch lock nut.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }

  1. E150073
    Connect the connector.


6. INSPECT AND ADJUST BRAKE PEDAL HEIGHT

  1. Check the brake pedal height.

    1. C165370E03
      Turn back the carpet.
      Text in Illustration 
      *1
      Stop Light Switch Assembly
      *2
      Clevis Lock Nut
      *3
      Front Floor Footrest (for LHD)
      No. 2 Dash Panel Insulator Pad (for RHD)
      *a
      Brake Pedal Height

    2. Measure the shortest distance between the brake pedal surface and front floor footrest (for LHD) or No. 2 dash panel insulator pad (for RHD).

      Pedal height (for LHD: from front floor footrest, for RHD: No. 2 dash panel insulator pad) 
      Model
      Specified Condition
      LHD
      148.8 to 158.8 mm (5.858 to 6.252 in.)
      RHD
      165.9 to 175.9 mm (6.531 to 6.925 in.)

  1. Adjust the brake pedal height.

    1. Disconnect the stop light switch connector.

    2. Remove the stop light switch assembly.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the brake pedal height by turning the push rod.

    5. Tighten the push rod clevis lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. Install and adjust the stop light switch (Click here).

      NOTICE:
      Do not depress the brake pedal.

    7. Connect the stop light switch connector.


7. INSPECT BRAKE PEDAL FREE PLAY

  1. C132708E01
    Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.

  1. Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance (Click here). If the pedal free play is as specified, proceed to the "INSPECT BRAKE PEDAL RESERVE DISTANCE" procedure.


8. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.

  1. Release the parking brake.

  1. C111339E13
    With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.
    Text in Illustration 
    *1
    Front Floor Footrest (for LHD)
    No. 2 Dash Panel Insulator Pad (for RHD)
    *a
    Pedal Reserve Distance

    Pedal reserve distance at 500 N (51 kgf, 112 lbf) (for LHD: from front floor footrest, for RHD: from No. 2 dash panel insulator pad):
    Model
    Specified Condition
    LHD
    84.4 mm (3.32 in.)
    RHD
    97.8 mm (3.85 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).


9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


12. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.

← REASSEMBLY (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →