2007-2013 Highlander Kluger · Service Manual BRAKE

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD

NOTICE:
Make an adjustment with no vacuum in the brake booster assembly. (Depress the brake pedal several times with the engine stopped.)

HINT:
  1. Adjustment of the brake booster push rod is required when the brake master cylinder sub-assembly is replaced with a new one.
  1. Adjustment is not necessary when the removed brake master cylinder sub-assembly is reused and the brake booster assembly is replaced with a new one.

  1. Apply chalk to the tip of the accessory tool.

    HINT:
    An accessory tool is enclosed with a new brake master cylinder sub-assembly.

  1. C132707E01
    Place the accessory tool on the brake booster assembly.

  1. Measure the clearance between the brake booster push rod and accessory tool.

    Standard clearance:
    0 mm (0 in.)

    HINT:
    Adjust the clearance in the following cases:

    1. If there is a clearance between the accessory tool and the shell of the brake booster (floating accessory tool), the push rod is protruding too far.
    2. If the chalk does not stick on the tip of the brake booster push rod, the push rod protrusion is insufficient.

  1. C132720E01
    If the clearance is not as specified, adjust the push rod length by holding the rod using SST and turning the tip of the rod using a socket driver (7 mm).
    SST
    09737-00020  

    HINT:
    Check the push rod clearance again after adjustment.


2. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for LHD)
  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. C165944
    Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. When installing the master cylinder to the brake booster, or when removing the master cylinder from the brake booster, make sure that the master cylinder is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling out.
    4. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a shop rag or a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the piston.
    5. Do not use any other type of grease or fluid.


3. CONNECT BRAKE LINE (for LHD)

  1. C165943E01
    Using a union nut wrench (12 mm), connect the 2 brake lines to the brake master cylinder sub-assembly.

    Torque:
    without union nut wrench:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    with union nut wrench:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.


4. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (for RHD)
  1. Install a new O-ring to the brake master cylinder sub-assembly.

  1. C165947
    Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

    NOTICE:
    1. The master cylinder requires careful handling. Do not allow the master cylinder to receive any impact, such as from being dropped. Do not reuse a master cylinder that has been dropped.
    2. Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.
    3. When installing the master cylinder to the brake booster, or when removing the master cylinder from the brake booster, make sure that the master cylinder is kept horizontal or its tip faces downward (the piston faces upward) to prevent the master cylinder piston from falling out.
    4. Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the piston, remove it by using a shop rag or a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the piston.
    5. Do not use any other type of grease or fluid.


5. CONNECT BRAKE LINE (for RHD)

  1. C165946E01
    Using a union nut wrench (12 mm), connect the 2 brake lines to the brake master cylinder sub-assembly.

    Torque:
    without union nut wrench:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    with union nut wrench:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.


6. CONNECT NO. 1 RESERVOIR TUBE
  1. Connect the No. 1 reservoir tube to the brake master cylinder reservoir assembly.


7. FILL BRAKE FLUID RESERVOIR

  1. C165889
    Fill the reservoir with brake fluid.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3

    NOTICE:
    Make sure that there is sufficient brake fluid in the reservoir.


8. BLEED BRAKE MASTER CYLINDER

NOTICE:
  1. If the master cylinder is reinstalled or if the reservoir becomes empty, bleed the master cylinder.
  2. To prevent brake fluid from adhering, cover the painted surfaces with a shop rag or a piece of cloth.

  1. C165942
    Using a union nut wrench (12 mm), disconnect the 2 brake lines from the master cylinder.

  1. C165891
    Slowly depress the brake pedal and hold it (*1).

  1. C165893
    Cover the 2 outer holes with fingers, and release the brake pedal (*2).

  1. Repeat (*1) and (*2) 3 or 4 times.

  1. C165943E01
    Using a union nut wrench (12 mm), connect the 2 brake lines to the master cylinder.

    Torque:
    w/o union nut wrench:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }
    w/ union nut wrench:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque value is effective when the union nut wrench is parallel to the torque wrench.


9. BLEED BRAKE LINE

NOTICE:
  1. Bleed the brake line of the wheel farthest from the master cylinder first.
  2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

  1. C165894
    Connect a vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed (*3).

  1. C165895
    When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*4).

  1. Repeat (*3) and (*4) until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug completely.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Repeat the above procedure for each wheel to bleed the brake line.


10. BLEED BRAKE ACTUATOR

NOTICE:
After bleeding the brake system, if the specified height or feel of the brake pedal cannot be obtained, bleed the brake actuator assembly with the intelligent tester by following the procedure below.

  1. Depress the brake pedal more than 20 times with the ignition switch off.

  1. Connect the intelligent tester to the DLC3, and then turn the ignition switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester on and select "AIR BLEEDING" on the screen.

    NOTICE:
    1. Refer to the intelligent tester operator's manual for further details.
    2. Bleed the air by following the steps displayed on the intelligent tester.

  1. Bleed the air according to "Step 1: Increase" on the intelligent tester display.

    NOTICE:
    1. Make sure that the master cylinder reservoir tank does not run out of brake fluid.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.


    1. C165894
      Connect a vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*5).

    3. C165895
      When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*6).

    4. Repeat (*5) and (*6) until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    6. Repeat the above procedure for the rest of the wheels to bleed the brake lines.

  1. Bleed the suction line according to "Step 2: Inhalation" on the intelligent tester display.

    NOTICE:
    1. Bleed the suction line by following the steps displayed on the intelligent tester.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.


    1. C165896
      Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator assembly to bleed the air using the intelligent tester (*7).

      NOTICE:
      1. During this step, be sure to release the brake pedal.
      2. The actuator operation stops automatically in 4 seconds.

    3. C165897
      Check that the actuator operation has stopped by referring to the intelligent tester display, and tighten the bleeder plug (*8).

    4. Repeat (*7) and (*8) until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    6. For the rest of the wheels, bleed the air in the same way as stated in the above procedure.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

  1. Bleed the pressure reduction line according to "Step 3: Decrease" on the intelligent tester display.

    NOTICE:
    1. Bleed the pressure reduction line by following the steps displayed on the intelligent tester.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.


    1. C165898
      Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (*9).

    3. While keeping the brake pedal fully depressed, operate the brake actuator assembly using the intelligent tester.

      NOTICE:
      1. The actuator operation stops automatically in 4 seconds. When performing this procedure continuously, an interval of at least 20 seconds is required.
      2. After the operation is completed, the brake pedal goes down slightly. This is a normal phenomenon when the solenoid opens.
      3. During this procedure, the pedal seems heavy, but completely depress it so that the brake fluid comes out from the bleeder plug.
      4. Be sure to keep the brake pedal depressed. Never depress and release the pedal repeatedly.

    4. C165895
      Tighten the bleeder plug, and then release the brake pedal (*10).

    5. Repeat steps (*9) to (*10) until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    7. Repeat the above procedures for the rest of the brakes to bleed the brake line.

  1. Bleed the brake lines again according to "Step 4: Increase" on the intelligent tester display.

    NOTICE:
    1. Bleed the air by following the steps displayed on the intelligent tester.
    2. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.


    1. C165898
      Connect a vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, and then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*11).

    3. C165895
      When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal (*12).

    4. Repeat (*11) and (*12) until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    6. Repeat the above procedures for each brake to bleed the brake lines.

  1. Finish "AIR BLEEDING" on the intelligent tester, and then turn off the tester.

  1. Disconnect the intelligent tester from the DLC3.

  1. Turn the ignition switch off.


11. INSPECT FOR BRAKE FLUID LEAK

12. INSPECT FLUID LEVEL

  1. C269142E01
    Check the fluid level.
    If brake fluid level is lower than the MIN line, check for leaks and inspect the disc brake pads. If necessary, refill the reservoir with brake fluid to the MAX line after repair or replacement.

    Brake Fluid:
    SAE J1703 or FMVSS No. 116 DOT 3


13. INSTALL CHARCOAL CANISTER ASSEMBLY (for LHD)

  1. A170963
    Install the charcoal canister assembly with the 2 bolts.

    Torque:
    26.5 N*m{ 270 kgf*cm , 20 ft.*lbf }

  1. A170962
    Connect the 2 hoses.


14. INSTALL AIR CLEANER CASE SUB-ASSEMBLY (for LHD)

  1. A170450
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.


15. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY (for LHD)

16. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (for LHD)

  1. A171941E01
    Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. A170887
    Connect the 3 vacuum hoses.

  1. A171944
    Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.


17. INSTALL NO. 2 AIR CLEANER INLET (for LHD)

  1. A170453
    Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.


18. INSTALL COOL AIR INTAKE DUCT SEAL (for LHD)

  1. A170196
    Install the cool air intake duct seal with the 11 clips.


19. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C165926E01
    Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

  1. C165925
    Engage the 4 clamps.


20. INSTALL WINDSHIELD WIPER MOTOR AND LINK

  1. E150150
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


21. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Engage the 20 claws.

    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.

  1. E150146
    Engage the 2 claws and connect the front fender to cowl side seal LH.

  1. E150147
    Engage the 2 claws and connect the front fender to cowl side seal RH.


22. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E147125E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)


23. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E152618E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

← REASSEMBLY (from May 2007)INSTALLATION (Aug 2008 – Jun 2010) →