2007-2013 Highlander Kluger · Service Manual BODY

INSPECTION

Inspection · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

  1. Disconnect the mirror connector.

    B176183E05

  1. Apply battery voltage and check the operation of the mirror.

    OK:
    w/o Mirror Heater
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 1 (M+)
    Turns upward
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward
    Battery positive (+) → Terminal 2 (MH)
    Battery negative (-) → Terminal 1 (M+)
    Turns left
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 2 (MH)
    Turns right
    w/ Mirror Heater
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 7 (M+)
    Turns upward
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward
    Battery positive (+) → Terminal 6 (MH)
    Battery negative (-) → Terminal 7 (M+)
    Turns left
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 6 (MH)
    Turns right

    If the result is not as specified, replace the mirror assembly.

  1. w/ Mirror Heater:

    B261870E01
    Check the resistance.

    1. Measure the resistance according to the value(s) in the table bellow.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (H+) - 1 (H-)
      Always
      3.8 to 4.8 Ω

      If the result is not as specified, replace the outer rear view mirror.

    2. Connect the cable from the positive battery (+) terminal to terminal 2 and the negative battery (-) terminal to terminal 1, then check that the mirror becomes warm.

      OK:
      Mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror.


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

  1. Disconnect the mirror connector.

    B176185E06

  1. Apply battery voltage and check the operation of the mirror.

    OK:
    w/o Mirror Heater
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 1 (M+)
    Turns upward
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward
    Battery positive (+) → Terminal 2 (MH)
    Battery negative (-) → Terminal 1 (M+)
    Turns left
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 2 (MH)
    Turns right
    w/ Mirror Heater
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 1 (M+)
    Turns upward
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward
    Battery positive (+) → Terminal 2 (MH)
    Battery negative (-) → Terminal 1 (M+)
    Turns left
    Battery positive (+) → Terminal 1 (M+)
    Battery negative (-) → Terminal 2 (MH)
    Turns right

    If the result is not as specified, replace the mirror assembly.

  1. w/ Mirror Heater:

    B261871E01
    Check the resistance.

    1. Measure the resistance according to the value(s) in the table bellow.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (H+) - 1 (H-)
      Always
      3.8 to 4.8 Ω

      If the result is not as specified, replace the outer rear view mirror.

    2. Connect the cable from the positive battery (+) terminal to terminal 2 and the negative battery (-) terminal to terminal 1, then check that the mirror becomes warm.

      OK:
      Mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror.

← INSPECTION (May 2007 – Jun 2010)REASSEMBLY (from Jul 2010) →