2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

B2785 Communication Malfunction between ECUs Connected by LIN

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification ECU (smart key ECU assembly) system LIN bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification ECU (smart key ECU assembly) system LIN bus lines at a set interval and 3 times in a row, DTC B2785 will be output.
DTC No.
DTC Detection Condition
Trouble Area
B2785
  1. Error in LIN communication between ECUs and an open or short in communication lines
  2. LIN communication from certification ECU (smart key ECU assembly) stops for a set amount of time or more
  1. Certification ECU (Smart key ECU assembly)
  2. Main body ECU (Instrument panel junction block assembly)
  3. Steering lock ECU (Steering lock actuator assembly)
  4. ID code box (Immobiliser code ECU)
  5. Wire harness

WIRING DIAGRAM

B162902E15

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.


1. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)
  1. Disconnect the D36 connector.

  1. Disconnect the 1E connector.

  1. Disconnect the D28 connector.

  1. Disconnect the D10 connector.B177006E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-10 (LIN) - D28-3 (LIN1)
    Always
    Below 1 Ω
    D36-10 (LIN) - 1E-7 (LIN1)
    Always
    Below 1 Ω
    D36-10 (LIN) - D10-5 (LIN)
    Always
    Below 1 Ω
    D36-10 (LIN) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D36-10 (LIN) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK FOR DTC
  1. Connect the D36, D28 and D10 connectors.

  1. Check for DTC.

    Result:
    Result
    Proceed to
    B2785 is output
    A
    B2785 is not output
    B



B
Go to step 5
A


3. CHECK FOR DTC
  1. Connect the 1E connector.

  1. Disconnect the D10 connector.

  1. Check for DTC.

    Result:
    Result
    Proceed to
    B2785 is output
    A
    B2785 is not output
    B



B
Go to step 7
A


4. CHECK FOR DTC
  1. Connect the D10 connector.

  1. Disconnect the D28 connector.

  1. Check for DTC.

    Result:
    Result
    Proceed to
    B2785 is output
    A
    B2785 is not output
    B



B
Go to step 9
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5. REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
  1. Replace the main body ECU with a normally-functioning or a new one.


NEXT


6. CHECK FOR DTC
  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2785 is not output
    A
    B2785 is output
    B



B
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A

END

7. REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
  1. Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).


NEXT


8. CHECK FOR DTC
  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2785 is not output
    A
    B2785 is output
    B



B
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A

END

9. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU) with a new one.


NEXT


10. CHECK FOR DTC
  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2785 is not output
    A
    B2785 is output
    B



B
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
A

END


← B2325 LIN Communication Bus Malfunction (from Jul 2010)B2785 Communication Malfunction between ECUs Connected by LIN (Aug 2008 – Jun 2010) →