2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

B2325 LIN Communication Bus Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The main body ECU (instrument panel junction block assembly) monitors communication between all the ECUs connected to the door system LIN bus lines. When the main body ECU (instrument panel junction block assembly) detects errors in communication with all the ECUs connected to the door system LIN bus lines at 2.6-second intervals and 3 times in a row, DTC B2325 will be output.
DTC No.
DTC Detection Condition
Trouble Area
B2325
Main body ECU (instrument panel junction block assembly) detects errors in communication with the ECUs connected to the door system LIN bus lines 3 times in a row.
  1. Front power window regulator motor assembly LH*1
  2. Front power window regulator motor assembly RH*2
  3. Sliding roof ECU (Sliding roof drive gear sub-assembly)*3
  4. Main body ECU (Instrument panel junction block assembly)
  5. Wire harness

HINT:
*1: for LHD
*2: for RHD
*3: w/ Sliding Roof


WIRING DIAGRAM

B162897E07

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.


1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

HINT:
*1: for LHD
*2: for RHD
*3: w/ Sliding Roof

B172345E02
  1. Disconnect the D8 connector.

  1. Disconnect the H1*1 or G10*2 connector.

  1. Disconnect the Q12*3 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D8-10 (LIN2) - H1*1-9 (LIN)
    Always
    Below 1 Ω
    D8-10 (LIN2) - G10*2-9 (LIN)
    Always
    Below 1 Ω
    D8-10 (LIN2) - Q12*3-4 (MPX1)
    Always
    Below 1 Ω
    D8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D8-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result:
    Result
    Proceed to
    Models with Sliding roof
    A
    Models without Sliding roof
    B



B
Go to step 5
A


3. CHECK FOR DTC (SLIDING ROOF ECU)

HINT:
*1: for LHD
*2: for RHD

  1. Connect the D8 connector.

  1. Connect the H1*1or G10*2 connector.

  1. Check for DTC.

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output
    B



B
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (Click here)
A


4. CHECK FOR DTC (POWER WINDOW ECU)

HINT:
*1: for LHD
*2: for RHD
*3: w/ Sliding Roof

  1. Connect the Q12*3 connector.

  1. Disconnect the H1*1 or G10*2 connector.

  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2325 is output
    A
    B2325 is not output (for LHD)
    B
    B2325 is not output (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

5. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH*1/RH*2

HINT:
*1: for LHD
*2: for RHD

  1. Replace the front power window regulator motor assembly LH*1 or RH*2with a normally-functioning or a new one (Click here).


NEXT


6. CHECK FOR DTC
  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2325 is not output
    A
    B2325 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
A

END


← B2325 LIN Communication Bus Malfunction (Aug 2008 – Jun 2010)B2785 Communication Malfunction between ECUs Connected by LIN (May 2007 – Jul 2008) →