2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

B2321 Driver Side Door ECU Communication Stop

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This DTC is output when LIN communication between the front power window regulator motor assembly LH*1/RH*2 and main body ECU (instrument panel junction block assembly) stops for more than 10 seconds.

HINT:
*1: for LHD
*2: for RHD

DTC No.
DTC Detection Condition
Trouble Area
B2321
No communication between front power window regulator motor assembly LH*1/RH*2 and main body ECU (instrument panel junction block assembly) for more than 10 seconds
  1. Front power window regulator motor assembly LH*1
  2. Front power window regulator motor assembly RH*2
  3. Main body ECU (Instrument panel junction block assembly)
  4. Wire harness

WIRING DIAGRAM

B176995E06
B176995E07

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn the courtesy switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.


1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR LH*1/RH*2)

HINT:
*1: for LHD
*2: for RHD

B175415E01
  1. Disconnect the D8 connector.

  1. Disconnect the H1*1 or G10*2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D8-10 (LIN2) - H1*1-9 (LIN)
    Always
    Below 1 Ω
    D8-10 (LIN2) - G10*2-9 (LIN)
    Always
    Below 1 Ω
    D8-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D8-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH*1/RH*2

HINT:
*1: for LHD
*2: for RHD

  1. B172344E05
    Disconnect the H1*1 or G10*2 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    H1*1-2 (B) - Body ground
    G10*2-2 (B) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    H1*1-2 (B) - Body ground
    G10*2-2 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH*1/RH*2

HINT:
*1: for LHD
*2: for RHD

  1. Replace the front power window regulator motor assembly LH*1 or RH*2with a normally-functioning or a new one (Click here).

  1. Clear the DTC.


NEXT


4. CHECK FOR DTC
  1. Recheck for DTC.

    Result:
    Result
    Proceed to
    B2321 is not output
    A
    B2321 is output
    B



B
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
A

END


← B2321 Driver Side Door ECU Communication Stop (May 2007 – Jul 2008)B2321 Driver Side Door ECU Communication Stop (from Jul 2010) →