2007-2013 Highlander Kluger · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010

HINT:
When installing the side mudguard, heat the vehicle body and side mudguard using a heat light.

Heating temperature:
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Side Mudguard
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or side mudguard excessively.


1. INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the upper rear door outside moulding pad from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B172804E01
    Clean the rear door outside moulding sub-assembly. (If reusing the rear door outside moulding sub-assembly)

    1. Using a heat light, heat the rear door outside moulding sub-assembly.

    2. Remove the upper rear door outside moulding pad from the rear door outside moulding sub-assembly.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Install a new upper rear door outside moulding pad to the rear door outside moulding sub-assembly.

  1. Install 2 new No. 3 clips on the rear door outside moulding sub-assembly.

  1. Install 6 new No. 4 clips on the rear door outside moulding sub-assembly.

  1. Install a new gasket on the rear door outside moulding sub-assembly.

  1. B172803E01
    Install the rear door outside moulding sub-assembly.

    1. Using a heat light, heat the vehicle body and rear door outside moulding sub-assembly.

    2. Remove the release paper from the rear door outside moulding sub-assembly.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 8 clips and install the rear door outside moulding sub-assembly.

  1. B172802
    Install the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the rear door No. 2 weatherstrip.


2. INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the upper front door outside moulding pad from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B172801E01
    Clean the front door outside moulding sub-assembly. (If reusing the front door outside moulding sub-assembly)

    1. Using a heat light, heat the front door outside moulding sub-assembly.

    2. Remove the upper front door outside moulding pad from the front door outside moulding sub-assembly.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Install a new upper front door outside moulding pad to the front door outside moulding sub-assembly.

  1. Install 3 new No. 3 clips on the front door outside moulding sub-assembly.

  1. Install 8 new No. 4 clips on the front door outside moulding sub-assembly.

  1. Install a new gasket on the front door outside moulding sub-assembly.

  1. B172800E01
    Install the front door outside moulding sub-assembly.

    1. Using a heat light, heat the vehicle body and front door outside moulding sub-assembly.

    2. Remove the release paper from the front door outside moulding sub-assembly.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 11 clips and install the front door outside moulding sub-assembly.

  1. B172799
    Install the nut.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the front door weatherstrip.


3. INSTALL FRONT FENDER OUTSIDE MOULDING PAD

  1. B172798E01
    Wipe off any tape adhesive residue with cleaner.

  1. Remove the release paper from the front fender outside moulding pad.

  1. Install a new front fender outside moulding pad to the front fender moulding sub-assembly.


4. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the front fender side protector from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B172797E01
    Clean the front fender moulding sub-assembly. (If reusing the front fender moulding sub-assembly)

    1. Using a heat light, heat the front fender moulding sub-assembly.

    2. Remove the front fender side protector from the front fender moulding sub-assembly.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Install a new front fender side protector to the the front fender moulding sub-assembly.

  1. Install 2 new No. 4 clips on the front fender moulding sub-assembly.

  1. Install a new pad on the front fender moulding sub-assembly.

  1. B172796
    Install the front fender moulding sub-assembly.

    1. Using a heat light, heat the vehicle body and the front fender moulding sub-assembly.

    2. Remove the release paper from the front fender moulding sub-assembly.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 3 clips and install the front fender moulding sub-assembly.

  1. B172795
    Using a 4 mm hexagon wrench, install the screw.

  1. Install the clip.

← REMOVAL (from Jul 2010)INSTALLATION (from Jul 2010) →