Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Standard measurement:
Area
Specified Condition
a
20.0 mm (0.787 in.)
b
15.0 mm (0.590 in.)
NOTICE:
Apply Primer M in front of the bead as shown in the illustration.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover Primer M.
Do not apply too much primer.
Using a brush or sponge, apply Primer G to the contact surface of the glass.
Standard measurement:
Area
Specified Condition
a
4.0 mm (0.157 in.)
b
12.0 mm (0.472 in.)
c
5.5 mm (0.216 in.)
d
10.3 mm (0.405 in.)
e
9.5 mm (0.374 in.)
f
6.0 mm (0.236 in.)
HINT:
If the primer is applied to an area that is specified, wipe off the primer with a non-residue solvent before it dries.
NOTICE:
To prevent the glass from breaking at low temperatures, ensure that no primer adheres to the contact surface between the moulding and glass during application.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover Primer G.
Do not apply too much primer.
Apply adhesive to the quarter window assembly.
Adhesive:
Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
Standard measurement:
Area
Specified Condition
a
6.0 mm (0.236 in.)
b
8.0 mm (0.315 in.)
c
12.0 mm (0.472 in.)
d
5.5 mm (0.216 in.)
e
9.5 mm (0.374 in.)
HINT:
After cutting off the tip, use all the adhesive within the time written in the table below.
Usage time frame:
Temperature
Usage Time Frame
35°C (95°F)
15 minutes
20°C (68°F)
1 hour and 40 minutes
5°C (41°F)
8 hours
Load the sealer gun with the cartridge.
Apply adhesive to the quarter window glass as shown in the illustration.
Install the quarter window glass to the vehicle body.
Hold the quarter window assembly in place securely with protective tape or equivalent until the adhesive hardens.
NOTICE:
Allow the primer to dry for 3 minutes or more.
Check that the clips are attached to the body correctly.
Check the clearance between the body and glass.
Lightly press the outer surface of the glass to ensure a close fit.
Using a scraper, remove any excess or protruding adhesive.
HINT:
Apply adhesive onto the glass rim.
NOTICE:
Do not drive the vehicle within the time written in the table below.
Minimum time:
Temperature
Minimum time prior to driving vehicle
35°C (95°F)
1 hour and 30 minutes
20°C (68°F)
5 hours
5°C (41°F)
24 hours
2.
INSPECT FOR LEAK AND REPAIR
Conduct a leak test after the adhesive has completely hardened.
Engage the 2 guides and install the No. 2 deck board sub-assembly.
78.
INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
Engage the 2 guides and install the No. 3 deck board sub-assembly.
79.
INSTALL DECK BOARD ASSEMBLY
Install the deck board sub-assembly.
80.
INSTALL CENTER PILLAR GARNISH LH
Engage the 2 guides and the clip.
Install the center pillar garnish LH with the clip and screw.
81.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Install the floor end of the front seat outer belt assembly with the bolt.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Check if the ELR locks.
NOTICE:
The check should be performed with the outer belt assembly installed.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
82.
INSTALL LOWER CENTER PILLAR GARNISH LH
Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.
83.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
NOTICE:
After installation, check that the corners fit correctly.
84.
INSTALL REAR DOOR SCUFF PLATE LH
Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.
85.
INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Install a new clip <A> on the front pillar garnish LH.
Engage the 3 guides and 2 clips, then install the front pillar garnish LH.
86.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
NOTICE:
After installation, check that the corners fit correctly.
87.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Engage the claw and clip, install the cowl side trim sub-assembly LH.
Install the clip.
88.
INSTALL FRONT DOOR SCUFF PLATE LH
Engage the guide and the 8 claws, and install the front door scuff plate LH.
89.
INSTALL CENTER PILLAR GARNISH RH
HINT:
Use the same procedure for the RH side and the LH side.
90.
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
91.
INSTALL LOWER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure for the RH side and the LH side.
92.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
NOTICE:
After installation, check that the corners fit correctly.
93.
INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH side and the LH side.
94.
INSTALL FRONT PILLAR GARNISH RH
Remove the protective cover.
Install a new clip <A> on the front pillar garnish RH.
Engage the 3 guides and 2 clips, then install the front pillar garnish RH.
95.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
NOTICE:
After installation, check that the corners fit correctly.
96.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure for the RH side and the LH side.
97.
INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure for the RH side and the LH side.
98.
INSTALL REAR NO. 1 SEAT ASSEMBLY LH
Temporarily install the 2 bolts on the front side of the seat.
Temporarily install the 3 bolts on the rear side of the seat.
Install the rear No. 1 seat assembly with the 5 bolts.