INSTALLATION
Removal / installation · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1. INSTALL QUARTER WINDOW ASSEMBLY |
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.


- Standard measurement:
Area
Specified Condition
a
20.0 mm (0.787 in.)
b
15.0 mm (0.590 in.)
- NOTICE:
- Apply Primer M in before the bead, as shown in the illustration.
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover Primer M.
- Do not apply too much primer.
- Apply Primer M in before the bead, as shown in the illustration.
Using a brush or sponge, apply Primer G to the contact surface of the moulding, in the location shown in the illustration.


- Standard measurement:
Area
Specified Condition
a
4.0 mm (0.157 in.)
b
12.0 mm (0.472 in.)
c
7.0 mm (0.276 in.)
d
10.3 mm (0.405 in.)
e
9.5 mm (0.374 in.)
f
6.0 mm (0.236 in.)
- HINT:
- If the primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.
- NOTICE:
- To prevent the glass from breaking at low temperatures, ensure that no primer adheres to the contact surface between the moulding and glass during application.
- Allow the primer to dry for 3 minutes or more.
- Throw away any leftover Primer G.
- Do not apply too much primer.
- To prevent the glass from breaking at low temperatures, ensure that no primer adheres to the contact surface between the moulding and glass during application.
Apply adhesive to the quarter window assembly.
- Adhesive:
- Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.


- Standard measurement:
Area
Specified Condition
a
6.0 mm (0.236 in.)
b
8.0 mm (0.315 in.)
c
12.0 mm (0.472 in.)
d
7.0 mm (0.276 in.)
e
9.5 mm (0.374 in.)
- HINT:
- After cutting off the tip, use all the adhesive within the time written in the table below.
- Usage time frame:
Temperature
Usage Time Frame
35°C (95°F)
15 minutes
20°C (68°F)
1 hour and 40 minutes
5°C (41°F)
8 hours
Load the sealer gun with the cartridge.
Apply adhesive to the quarter window glass as shown in the illustration.
Install the quarter window glass to the vehicle body.
Hold the quarter window assembly in place securely with protective tape or equivalent until the adhesive hardens.
- NOTICE:
- Allow the primer to dry for 3 minutes or more.
- Check that the clips are attached to the body correctly.
- Check the clearance between the body and glass.
- Allow the primer to dry for 3 minutes or more.
Lightly press the outer surface of the glass to ensure a close fit.
Using a scraper, remove any excess or protruding adhesive.

- HINT:
- Apply adhesive onto the glass rim.
- NOTICE:
- Do not drive the vehicle within the time written in the table below.
- Minimum time:
Temperature
Minimum time prior to driving vehicle
35°C (95°F)
1 hour and 30 minutes
20°C (68°F)
5 hours
5°C (41°F)
24 hours
| 2. INSPECT FOR LEAK AND REPAIR |
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
| 3. INSTALL ROOF HEADLINING ASSEMBLY |
