2007-2013 Highlander Kluger · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


1. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY

  1. B205743E01
    Temporarily install the 2 bolts <C>, 2 washers and the No. 2 seat cushion frame sub-assembly.

  1. Temporarily install the 2 bolts <B> and the 2 bushes.

  1. Temporarily install the 2 nuts, 2 bolts <A>, 2 springs and the 2 E-rings.

  1. Tighten the 2 nuts, 2 bolts <B> and the 2 bolts <C> to install the No. 2 seat cushion frame sub-assembly.

    Torque:
    Nut:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }
    Bolt <B>, Bolt <C>:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


2. INSTALL NO. 1 REAR SEAT LOCK CABLE ASSEMBLY RH

  1. B205742
    Connect the 2 cable clamps to install the No. 1 rear seat lock cable assembly RH.


3. INSTALL NO. 2 REAR SEAT CUSHION LOCK CABLE ASSEMBLY RH

  1. B205849
    Connect the 2 cable clamps and install the No. 2 rear seat cushion lock cable assembly RH.

  1. Install a new clamp.


4. INSTALL NO. 1 REAR SEAT LOCK CABLE ASSEMBLY LH

  1. B205740
    Connect the 2 cable clamps to install the No. 1 rear seat lock cable assembly LH.


5. INSTALL NO. 2 REAR SEAT CUSHION LOCK CABLE ASSEMBLY LH

  1. B205739
    Connect the 2 cable clamps and install the No. 2 rear seat cushion lock cable assembly LH.

  1. Install a new clamp.


6. INSTALL REAR SEATBACK EDGE PROTECTOR

  1. B205738
    Engage the 8 claws to install the 4 rear seatback edge protectors.


7. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY RH

  1. B205736
    Install the rear No. 2 seat headrest assembly RH with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the 2 cable clamps.

  1. B205734
    Install the rear No. 2 seat headrest cover RH with the 2 screws.


8. INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY LH

  1. B205737
    Install the rear No. 2 seat headrest assembly LH with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the 2 cable clamps.

  1. B205735
    Install the rear No. 2 seat headrest cover LH with the 2 screws.


9. INSTALL NO. 2 REAR SEAT RECLINING COVER RH

  1. B174471
    Engage the guide.

  1. Install the No. 2 rear seat reclining cover RH with the screw.


10. INSTALL NO. 2 REAR SEAT RECLINING COVER LH

  1. B174470
    Engage the guide.

  1. Install the No. 2 rear seat reclining cover LH with the screw.


11. INSTALL REAR NO. 2 SEATBACK COVER SUB-ASSEMBLY

  1. Using hog ring pliers, install the rear No. 2 seatback cover sub-assembly with 18 new hog rings.

    B174469E01

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


12. INSTALL REAR NO. 2 SEATBACK COVER WITH PAD
  1. Temporarily install the rear No. 2 seatback cover with pad to the rear No. 2 seatback frame sub-assembly.

  1. B206723
    Engage the 16 clips and install the rear No. 2 seatback cover.

  1. Engage the 15 hooks.

    B205732E01

  1. Using hog ring pliers, install the rear No. 2 seatback cover with pad with 4 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


13. INSTALL NO. 1 REAR SEAT COVER BEZEL

  1. B205730
    Install the No. 1 rear seat cover bezel to the No. 1 rear side seat band sub-assembly.

  1. B205728
    Engage the hook.

  1. Install the No. 1 rear seat cover bezel and the No. 1 rear side seat band sub-assembly with the 2 screws.


14. INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY

  1. Engage the 3 hooks.

    B205727

  1. Engage the 7 clips to install the No. 2 seatback board sub-assembly.


15. INSTALL REAR NO. 2 SEAT HANDLE

  1. Connect the 2 cable clamps as shown in the illustration.

    B173845

  1. B205726
    Install a new clamp.

  1. B173843
    Install the rear No. 2 seat handle with the 2 screws.


16. INSTALL REAR SEAT LOCK STRIKER COVER

  1. B173842
    Engage the 2 guides.

  1. Engage the claw to install the rear seat lock striker cover.


17. INSTALL NO. 1 REAR SIDE SEAT BAND SUB-ASSEMBLY

  1. B205722E01
    Attach the fastener.

  1. Install the seat track handle with the 2 new clips.


18. INSTALL REAR NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY

  1. Using hog ring pliers, install the rear No. 2 seat cushion cover sub-assembly with 14 new hog rings.

    B173840E01

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


19. INSTALL REAR NO. 2 SEAT CUSHION COVER WITH PAD

  1. Using hog ring pliers, install 4 new hog rings.

    B205848E01

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. Engage the 13 hooks to install the rear No. 2 seat cushion cover with pad.

    B206728


20. INSTALL NO. 2 SEAT HINGE COVER RH

  1. B173837
    Install the No. 2 seat hinge cover RH with the 2 screws.


21. INSTALL RECLINING COVER PROTECTOR RH

  1. B173836
    Install the reclining cover protector RH with the 2 screws.


22. INSTALL NO. 2 SEAT HINGE COVER LH

  1. B173835
    Install the No. 2 seat hinge cover LH with the 2 screws.


23. INSTALL RECLINING COVER PROTECTOR LH

  1. B173834
    Install the reclining cover protector LH with the 2 screws.

← DISASSEMBLY (from Jul 2010)REASSEMBLY (from Jul 2010) →