2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

OPERATION CHECK

Troubleshooting · Vehicles built from Jul 2012

Versions by build date: Jul 2010 – Jun 2012 from Jul 2012


CHECK SYSTEM NORMAL CONDITION
  1. If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.

    Symptom
    Answer
    A longer route than expected is chosen.
    Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
    Even when distance priority is high, the shortest route is not shown.
    Some routes may not be advised due to safety concerns.
    When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position.
    If the vehicle starts before the navigation system activates, the system may not react.
    When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position.
    When the vehicle is driving on new roads not available on the hard disk drive, the system attempts to match it to another nearby road, causing the position mark to deviate.

  2. I100066
    The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.

    1. The current position mark may be displayed on a nearby parallel road.

    2. I100067
      Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

    3. I100068
      When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

    4. I100069
      When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.

    5. I100070
      When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.

    6. I100071
      When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.

    7. I100072
      When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

    8. E106418
      When the ignition switch is turned to ACC or ON on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.

    9. I100074
      When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

    10. I100075
      When the tires are changed, the current vehicle position mark may deviate from the correct position.

      HINT:
      1. A change in tire diameter may cause a speed sensor error.
      2. Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.


CHECK HARD DISK DRIVE

HINT:
  1. Check the hard disk drive (HDD) built into the navigation receiver assembly.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176695
    Select "Failure Diagnosis" from the "Service Menu" screen.

  3. E181026E01
    Hard disk drive check

    1. Select "HDD Check" to start the HDD check.

    2. Check that the result is displayed when the HDD check is completed.

      Screen Description 
      Result
      Description
      Checking
      While the check is in progress
      OK
      Hard disk drive is normal
      NG
      Hard disk drive is malfunctioning

      HINT:
      1. After selecting "HDD Check", it may take a while until the result is displayed.
      2. Replace the navigation receiver assembly when NG is displayed.


CHECK PANEL & STEERING SWITCH

HINT:
  1. The navigation receiver assembly panel switches and steering switch are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210139
    Select "Panel & Steering Switch" from the "Function Check/Setting" screen.

  4. Panel & Steering Switch Check Mode

    1. E176522E05
      Operate each switch and check that the switch names and condition are correctly displayed.
      Screen Description 
      Display
      Content
      *1: Name of switch being pushed
      1. Name of the pushed switch is displayed.
      2. If more than one switch is pressed, "MULTIPLE" will be displayed.
      *2: Rotary switch name
      Name of the rotary switch is displayed.
      *3: Rotary switch direction
      Direction of the rotary switch is displayed.


CHECK TOUCH SWITCH

HINT:
  1. The touch switches on the screen are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210140
    Select "Touch Switch" from the "Function Check/Setting" screen.

  4. Touch Switch Check

    1. E176521
      Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

      HINT:
      1. A "+" mark is displayed where the display is touched.
      2. The "+" mark remains on the display even after the finger is removed.


CHECK MIC & VOICE RECOGNITION

HINT:
  1. The microphone and microphone input level are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210141
    Select "Mic & Voice Recognition" from the "Function Check/Setting" screen.

  4. Microphone & Voice Recognition Check

    1. E187218
      When speaking into the microphone, check that the microphone input level meter changes according to the input level.

    2. Push the recording switch and perform voice recording.

      HINT:
      1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
      2. Voice can be recorded up to 5 seconds.

    3. Check that the recording indicator remains on while recording and that the recording can be played normally.

      HINT:
      1. For details of this function, refer to Diagnosis Display Detailed Description in System Description (Click here).
      2. This function is controlled by the navigation receiver assembly (built-in navigation ECU).


CHECK COLOR BAR

HINT:
  1. The display color on the screen is checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210142
    Select "Color Bar" from the "Function Check/Setting" screen.

  4. Color Bar Check Mode

    1. E176520
      Select a color bar from the "Color Bar Check Mode" screen.

    2. Check the display color.

      HINT:
      1. The entire screen turns to the color or stripe selected.
      2. Touching the display will return to the "Color Bar Check Mode" screen.


CHECK GPS & VEHICLE SENSORS

HINT:
  1. GPS information, vehicle signals and sensor signals are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210143
    Select "GPS & Vehicle Sensors" from the "Function Check/Setting" screen.

  4. GPS information

    1. E176561
      When the "GPS Information" screen is displayed, check the GPS conditions.

      HINT:
      1. This screen is updated once per second when input signals to the vehicle are changed.
      2. For details of this function, refer to Diagnosis Display Detailed Description in System Description (Click here).

  5. Select "Sensors Check" from the "GPS information" screen.

  6. Vehicle Sensors

    1. E176525
      Check all the signals and sensors when vehicle signal information is displayed.

      HINT:
      1. This screen is updated once per second when input signals to the vehicle are changed.
      2. This screen displays vehicle signals input to the navigation receiver assembly (built-in navigation ECU).
      3. For details of this function, refer to Diagnosis Display Detailed Description in System Description (Click here).


CHECK VEHICLE SIGNALS

HINT:
  1. Vehicle signals received by the navigation receiver assembly are checked in the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210144
    Select "Vehicle Signal" from the "Function Check/Setting" screen.

  4. Vehicle Signal Check Mode

    1. E176523
      When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

      HINT:
      1. Only conditions having inputs are displayed.
      2. This screen displays vehicle signals input to the navigation receiver assembly (built-in navigation ECU).
      3. For details of this function, refer to Diagnosis Display Detailed Description in System Description (Click here).


CHECK SOUND LIBRARY SETTING

HINT:
  1. It is possible to turn the sound library function on and off and check the operation of the sound library function.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210145
    Select "Sound Library Setting" from the "Function Check/Setting" screen.

  4. E181113
    Sound Library Information

    HINT:
    1. For details of this function, refer to Diagnosis Display Detailed Description in System Description (Click here).
    2. This function is controlled by the navigation receiver assembly (built-in navigation ECU).


CHECK HANDS-FREE VOLUME SETTING

HINT:
  1. The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Enter diagnostic mode (Click here).

  2. E176696
    Select "Function Check/Setting" from the "Service Menu" screen.

  3. E210146
    Select "Hands-free Volume Setting" from the "Function Check/Setting" screen.

  4. Hands-free Volume Setting

    1. E235759E02
      Check the hands-free volume level.
      Screen Description 
      Display
      Content
      *1: Receive voice level adjustment
      Setting possible for the voice level received from "Bluetooth" compatible phones.
      *2: Send voice level adjustment
      Setting possible for the voice level sent from "Bluetooth" compatible phones.

      NOTICE:
      Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the receive voice quality is still acceptable after changing this setting.

      HINT:
      Sound quality of sent voice may deteriorate when the send voice level is adjusted.

← OPERATION CHECK (Jul 2010 – Jun 2012)PROBLEM SYMPTOMS TABLE (Jul 2010 – Jun 2012) →