2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

DTC CHECK / CLEAR

Troubleshooting · Vehicles built from Jul 2010


START DIAGNOSTIC MODE

HINT:
  1. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
  2. If the system cannot enter diagnostic mode, inspect all AVC-LAN communication components and repair or replace problem parts (Click here).
  3. After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

  1. There are 2 methods to start diagnostic mode. Start the mode by using either of them.

  2. E210038E01
    Method 1

    1. Start the engine.

    2. While pressing and holding the "INFO" switch, operate the light control switch: off → Turn on → Turn off → Turn on → Turn off → Turn on → Turn off.

    3. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

  3. Method 2

    1. Start the engine.

    2. E210039E01
      Press the "DISP" switch.

    3. E176528E01
      From the display quality adjustment screen, touch the corners of the screen in the following order: Upper left → Lower left → Upper left → Lower left → Upper left → Lower left.

    4. Diagnostic mode starts and the "Service Menu" screen will be displayed.


FINISH DIAGNOSTIC MODE
  1. Turn the ignition switch off.


FAILURE DIAGNOSIS

  1. E176743
    The "Failure Diagnosis" screen will be displayed by pressing the "Failure Diagnosis" switch on the "Service Menu" screen.


SYSTEM CHECK

  1. E210061
    The "System Check Mode" screen will be displayed by pressing the "System Check" switch on the "Failure Diagnosis" screen.


CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

HINT:
  1. Refer to Diagnosis Display Detailed Description for further details on the "System Check Mode" screen (Click here).
  2. When "NCON" is displayed for all devices connected using the AVC-LAN, or when all device names are not displayed, check if there is a short circuit in the AVC-LAN or devices connected to the AVC-LAN. Repair or replace parts as necessary (Click here).

  1. E210062E01
    Read the system check result.

    1. If the check result is "EXCH" or "CHEK", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

      NOTICE:
      A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.

      HINT:
      1. When all results are "OK", this means that no DTCs are present.
      2. When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

    2. Check the details of the DTC(s) (Click here).


DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

  1. E210063
    Clear DTC

    1. Press the "Memory CLR" switch for 3 seconds.

    2. Confirm that the check results are cleared.

      HINT:
      1. To clear the DTC for a specific device, clear the DTC using the "Unit Check Mode" screen.
      2. When clearing a DTC using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

  2. E210064
    Recheck

    1. Press the "Recheck" switch.

    2. E210065
      Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

      HINT:
      When a DTC was cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

← TERMINALS OF ECU (from Jul 2012)DIAGNOSTIC TROUBLE CODE CHART (from Jul 2010) →