2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1479/79 Flow Sensor Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

DESCRIPTION

The A/C flow sensor, which is mounted on the compressor and magnetic clutch, is used to detect the amount of refrigerant flow. The A/C flow sensor converts the amount of refrigerant flow that is detected to a voltage value to send it to the air conditioning amplifier. The voltage value sent from the A/C flow sensor changes depending on the amount of refrigerant flow. As the amount of refrigerant flow becomes larger, the voltage becomes lower. As the amount of refrigerant flow becomes smaller, the voltage becomes higher. The air conditioning amplifier supplies 5 V to the A/C flow sensor and monitors changes in the voltage value sent from the A/C flow sensor. The air conditioning amplifier then sends a signal to the ECM via CAN communication to allow the ECM to control the engine speed while the air conditioning is on.
DTC No.
DTC Detection Condition
Trouble Area
B1479/79
Open or short in A/C flow sensor circuit
  1. Compressor and magnetic clutch (A/C flow sensor)
  2. Harness or connector between Compressor and magnetic clutch (A/C flow sensor) and air conditioning amplifier
  3. Air conditioning amplifier

WIRING DIAGRAM

E159788E31

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Flow Sensor
    A/C flow sensor /
    Min.: 0 V
    Max.: 5 V
    Ignition switch on (IG): 0.3 to 4.7 V
    A/C flow sensor is malfunctioning when a constant value below 0.3 V or higher than 4.7 V is displayed continuously for more than 4 seconds.

    OK:
    The display is as specified in the Normal Condition column.


    Result:
    Result
    Proceed to
    OK (When troubleshooting according to Problem Symptoms Table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG (When a constant value below 0.3 V or higher than 4.7 V is displayed continuously for more than 4 seconds)
    C



B
REPLACE AIR CONDITIONING AMPLIFIER (Click here)

C
Go to step 3
A


2. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body Electrical / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/C Cutoff Signal
    A/C control cutoff signal /
    OFF or ON
    A/C switch on: OFF
    A/C switch off: ON
    -

    Result:
    Result
    Proceed to
    Value in Data List indicates OFF
    A
    Value in Data List indicates ON
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


3. REPLACE COMPRESSOR AND MAGNETIC CLUTCH (A/C FLOW SENSOR)
  1. Replace the A/C compressor (A/C flow sensor) (Click here).

    HINT:
    Since the compressor and magnetic clutch (A/C flow sensor) cannot be inspected while it is removed from the vehicle, replace the compressor and magnetic clutch (A/C flow sensor) with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1479/79 is not output
    A
    DTC B1479/79 is output
    B



B
Go to step 4
A

END

4. CHECK HARNESS AND CONNECTOR (COMPRESSOR AND MAGNET (A/C FLOW SENSOR) - A/C AMPLIFIER)

  1. E211184E06
    Disconnect the air conditioning amplifier connector.

  1. E213397E13
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D33-7 (FLOQ) - B53-3 (QUFL)
    Always
    Below 1 Ω
    D33-13 (SG-2) - B53-2 (SGFL)
    Always
    Below 1 Ω
    D33-30 (S5-1) - B53-1 (S5FL)
    Always
    Below 1 Ω
    D33-7 (FLOQ) - Body ground
    Always
    10 kΩ or higher
    D33-13 (SG-2) - Body ground
    Always
    10 kΩ or higher
    D33-30 (S5-1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


← B1451/51 Compressor Solenoid Circuit (from Jul 2010)B1497/97 BUS IC Communication Malfunction (May 2007 – Jul 2008) →