B1479/79 Flow Sensor Circuit
Diagnostic trouble codes · Vehicles built from Jul 2010
DESCRIPTION
The A/C flow sensor, which is mounted on the compressor and magnetic clutch, is used to detect the amount of refrigerant flow. The A/C flow sensor converts the amount of refrigerant flow that is detected to a voltage value to send it to the air conditioning amplifier. The voltage value sent from the A/C flow sensor changes depending on the amount of refrigerant flow. As the amount of refrigerant flow becomes larger, the voltage becomes lower. As the amount of refrigerant flow becomes smaller, the voltage becomes higher. The air conditioning amplifier supplies 5 V to the A/C flow sensor and monitors changes in the voltage value sent from the A/C flow sensor. The air conditioning amplifier then sends a signal to the ECM via CAN communication to allow the ECM to control the engine speed while the air conditioning is on.| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1479/79 |
Open or short in A/C flow sensor circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Flow Sensor
A/C flow sensor /
Min.: 0 V
Max.: 5 V
Ignition switch on (IG): 0.3 to 4.7 V
A/C flow sensor is malfunctioning when a constant value below 0.3 V or higher than 4.7 V is displayed continuously for more than 4 seconds.
- OK:
- The display is as specified in the Normal Condition column.
- Result:
Result
Proceed to
OK (When troubleshooting according to Problem Symptoms Table)
A
OK (When troubleshooting according to the DTC)
B
NG (When a constant value below 0.3 V or higher than 4.7 V is displayed continuously for more than 4 seconds)
C
|
|
||||
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
Air Conditioner Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
A/C Cutoff Signal
A/C control cutoff signal /
OFF or ON
A/C switch on: OFF
A/C switch off: ON
-
- Result:
Result
Proceed to
Value in Data List indicates OFF
A
Value in Data List indicates ON
B
|
|
||||
| A | |
| 3. REPLACE COMPRESSOR AND MAGNETIC CLUTCH (A/C FLOW SENSOR) |
Replace the Compressor and magnetic clutch (A/C flow sensor) (Click here).
- HINT:
- Since the Compressor and magnetic clutch (A/C flow sensor) cannot be inspected while it is removed from the vehicle, replace the compressor and magnetic clutch (A/C flow sensor) with a new or a known good one and check that the condition returns to normal.
Check for the DTC.
- Result:
Result
Proceed to
DTC B1479/79 is not output
A
DTC B1479/79 is output
B
|
|
||||
| A | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (COMPRESSOR AND MAGNET (A/C FLOW SENSOR) - A/C AMPLIFIER) |
Disconnect the air conditioning amplifier connector.

Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
D33-7 (FLOQ) - B51-3 (QUFL)
Always
Below 1 Ω
D33-13 (SG-2) - B51-2 (SGFL)
Always
Below 1 Ω
D33-30 (S5-1) - B51-1 (S5FL)
Always
Below 1 Ω
D33-7 (FLOQ) - Body ground
Always
10 kΩ or higher
D33-13 (SG-2) - Body ground
Always
10 kΩ or higher
D33-30 (S5-1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
