USB Audio System Recognition/Play Error
Circuit diagnosis · Vehicles built from Jul 2010
DESCRIPTION
When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the multi-media interface ECU. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- When a large amount of data is in a USB device, it may take a while to begin play.
- When using a USB device, files that are protected by copyright cannot be played.
- When files are not played in the sorted order, perform the following procedure before inspection.
- Add numbers in front of the file names.
- Put the files in a folder and copy the folder data to the USB device.
- When a large amount of data is in a USB device, it may take a while to begin play.
| 1. CHECK USB DEVICE OR "iPod" |
Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.
Check if playable files are present on the USB device or "iPod".
- HINT:
- Refer to System Description for playable files (Click here).
Check if the USB device is a compatible format or "iPod" is a compatible version.
- HINT:
- Refer to System Description for compatible formats and versions (Click here).
- Result:
Result
Proceed to
No playable files exist, or incompatible device format or version
A
Playable files exist, and compatible device format or version
B
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NO. 1 STEREO JACK ADAPTER) |
Disconnect the E28 multi-media interface ECU connector.

Disconnect the E27 No. 1 stereo jack adapter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E27-1 (UPI) - E28-4 (UPO)
Always
Below 1 Ω
E27-4 (UJSG) - E28-1 (UESG)
Always
Below 1 Ω
E27-2 (UDO-) - E28-3 (UDI-)
Always
Below 1 Ω
E27-3 (UDO+) - E28-2 (UDI+)
Always
Below 1 Ω
E27-5 (UJSS) - E28-5 (UESS)
Always
Below 1 Ω
E27-1 (UPI) - Body ground
Always
10 kΩ or higher
E27-4 (UJSG) - Body ground
Always
10 kΩ or higher
E27-2 (UDO-) - Body ground
Always
10 kΩ or higher
E27-3 (UDO+) - Body ground
Always
10 kΩ or higher
E27-5 (UJSS) - Body ground
Always
10 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Multi-media Interface ECU)
*b
Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE) |
Reconnect the E28 multi-media interface ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
E27-1 (UPI) - E27-4 (UJSG)
Ignition switch ACC
5 V
Text in Illustration *a
Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
|
|
||||
| OK | |
| 4. FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK |
Delete all files in the USB device or "iPod" and format/restore it.
Save the data again and check if it can be played on the in-vehicle device.
- NOTICE:
- Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.
- OK:
- Malfunction disappears.
|
|
||||
| OK | ||
| ||
| 5. REPLACE USB DEVICE OR "iPod" |
Turn the ignition switch off.
- HINT:
- When one of these DTCs has been stored, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.
Turn the ignition switch to ACC.
Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.
- HINT:
- If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
- Refer to System Description for compatible formats and versions (Click here).
- If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
| NEXT | |
| 6. CHECK USB Device or "iPod" |
Check if USB device or "iPod" is recognized by the multi-media interface ECU, if information such as track, artist and album names are displayed on the screen.
- OK:
- Malfunction disappears.
|
|
||||
| OK | ||
| ||
