2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

B15BB Multi-media Interface ECU Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

DESCRIPTION

This DTC is stored when a malfunction occurs in the multi-media interface ECU.
DTC No.
DTC Detection Condition
Trouble Area
B15BB
When one of the conditions below is met:
  1. System microprocessor malfunction
  2. Media interface microprocessor malfunction
  3. CD-LSI (Large Scale Integration) malfunction
  4. Internal power supply malfunction
  1. "iPod" or USB device
  2. Wire harness or connector
  3. No. 1 stereo jack adapter assembly
  4. Multi-media interface ECU

WIRING DIAGRAM

E210053E02

INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTC.


1. REPLACE "iPod" OR USB DEVICE
  1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

  1. Turn the ignition switch off.

    HINT:
    When this DTC has been stored, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.

  1. Turn the ignition switch to ACC.

  1. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

    HINT:
    If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.


NEXT


2. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


3. RECHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

USB DEVICE OR "iPod" WAS DEFECTIVE

4. INSPECT MULTI-MEDIA INTERFACE ECU

  1. E210105E15
    Disconnect the E27 No. 1 stereo jack adapter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E27-1 (UPI) - E27-4 (UJSG)
    Ignition switch ACC
    5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
Go to step 5
OK

REPLACE NO. 1 STEREO JACK ADAPTER ASSEMBLY (Click here)

5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA INTERFACE ECU - NO. 1 STEREO JACK ADAPTER)

  1. E210106E07
    Disconnect the E28 multi-media interface ECU connector.

  1. E210105E16
    Disconnect the E27 No. 1 stereo jack adapter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E28-4 (UPO) - E27-1 (UPI)
    Always
    Below 1 Ω
    E28-1 (UESG) - E27-4 (UJSG)
    Always
    Below 1 Ω
    E27-1 (UPI) - Body ground
    Always
    10 kΩ or higher
    E27-4 (UJSG) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multi-media Interface ECU)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTI-MEDIA INTERFACE ECU (Click here)


← B15B8 Harddisk Malfunction (from Jul 2012)B15C0 Short in GPS Antenna (+ B15C1) (from Jul 2010) →