DTC B1423/23 Pressure Sensor Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1423/23 |
|
|

| 1.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the connector from the A/C pressure sensor.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A11-3 (+) - Body ground | Ignition switch on (IG) | Approx. 5 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A11-1 (-) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.INSPECT A/C PRESSURE SENSOR (SENSOR SIGNAL CIRCUIT) |
Reconnect the connector to the A/C pressure sensor.
![]() |
Remove the Air Conditioning amplifier with connectors still connected.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-9 (PRE) - Body ground | Ignition switch on (IG) (A/C: OFF) | 0.5 to 4.8 V |
|
| ||||
| OK | |
| 4.INSPECT A/C PRESSURE SENSOR (SENSOR SIGNAL CIRCUIT) |
Measure the voltage when the following conditions are satisfied.
| Item | Condition |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | ON |
| R/F Switch | RECIRCULATION |
| Interior Temperature | 25 to 35°C (77 to 95°F) |
| Engine Speed | 2000 rpm |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-9 (PRE) - Body ground | Ignition switch on (IG) (A/C: ON) | 0.5 to 4.8 V |
| Result | Proceed to |
| OK (When troubleshooting according to DTC) | A |
| OK (When troubleshooting according to PROBLEM SYMPTOMS TABLE) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C PRESSURE SENSOR) |
![]() |
Disconnect the connector from the Air Conditioning amplifier.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A11-3 (+) - D37-10 (S5-3) | Always | Below 1 Ω |
| D37-10 (S5-3) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C PRESSURE SENSOR) |
![]() |
Disconnect the connector from the Air Conditioning amplifier.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A11-1 (-) - D37-13 (SG-2) | Always | Below 1 Ω |
| D37-13 (SG-2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C PRESSURE SENSOR) |
![]() |
Disconnect the connector from the Air Conditioning amplifier.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A11-2 (PR) - D37-9 (PRE) | Always | Below 1 Ω |
| D37-9 (PRE) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT FOR A/C SYSTEM LEAK |
Install the manifold gauge set.
Recover the refrigerant from the Air Conditioning system using a refrigerant recovery unit.
Evacuate the Air Conditioning system and check that vacuum can be maintained in it.
|
| ||||
| OK | |
| 9.CHARGE REFRIGERANT |
Add an appropriate amount of refrigerant (Click here).
| NEXT | |
| 10.RECHECK DTC |
Recheck for the DTC when the following conditions are satisfied.
| Item | Condition |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | ON |
| R/F Switch | RECIRCULATION |
| Interior Temperature | 25 to 35°C (77 to 95°F) |
| Engine Speed | 2000 rpm |
| Result | Proceed to |
| DTC B1423 is output | A |
| DTC B1423 is not output | B |
|
| ||||
| A | |
| 11.INSPECT A/C PRESSURE SENSOR |
Install the manifold gauge set.
Disconnect the connector from the A/C pressure sensor.
![]() |
Connect the three 1.5 V dry cell batteries' positive (+) lead to terminal 3, and the negative (-) lead to terminal 1.
Connect the voltmeter's positive (+) lead to terminal 2, and the negative (-) lead to terminal 1.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 - 1 | Refrigerant pressure: 0.39 to 3.187 MPa (57 to 463 psi) | 1.0 to 4.8 V |
|
| ||||
| OK | ||
| ||
| 12.REPAIR A/C SYSTEM LEAK |
Identify the area where refrigerant leaks from .
Repair the identified area of the Air Conditioning system.
Evacuate the A/C system.
| NEXT | ||
| ||
| 13.INSPECT COOLING FAN SYSTEM |
Check if that the cooling fan operates normally.
|
| ||||
| OK | |
| 14.CHARGE REFRIGERANT |
Use a refrigerant recovery unit to recover refrigerant.
Evacuate the Air Conditioning system.
Add an appropriate amount of refrigerant .
| NEXT | |
| 15.RECHECK DTC |
Recheck for the DTC when the following conditions are satisfied.
| Item | Condition |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | ON |
| R/F Switch | RECIRCULATION |
| Interior Temperature | 25 to 35°C (77 to 95°F) |
| Engine Speed | 2000 rpm |
| Result | Proceed to |
| DTC B1423 is output | A |
| DTC B1423 is not output | B |
|
| ||||
| A | |
| 16.REPLACE EXPANSION VALVE |
Replace the expansion valve with a normal one .
| NEXT | ||
| ||
| 17.CHARGE REFRIGERANT |
Add an appropriate amount of refrigerant .
| NEXT | |
| 18.RECHECK DTC |
Recheck for the DTC when the following conditions are satisfied.
| Item | Condition |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | ON |
| R/F Switch | RECIRCULATE |
| Interior Temperature | 25 to 35°C (77 to 95°F) |
| Engine Speed | 2000 rpm |
| Result | Proceed to |
| DTC B1423 is not output | A |
| DTC B1423 is output | B |
|
| ||||
| A | ||
| ||