COOLING FAN SYSTEM > Cooling Fan Circuit |
| 1.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE COOLING FAN) |
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cooling Fan.
Check the operation of the cooling fan while operating it using Techstream.
|
| ||||
| OK | ||
| ||
| 2.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU) |
Disconnect the D31 connector from the ECM.

Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D31-14 (RFC) - A9-2 (SI) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.INSPECT NO. 1 COOLING FAN MOTOR |
![]() |
Disconnect the No. 1 cooling fan motor connector.
Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 1 cooling fan motor connector.
|
| ||||
| OK | |
| 4.INSPECT NO. 2 COOLING FAN MOTOR |
![]() |
Disconnect the No. 2 cooling fan motor connector.
Connect the battery positive terminal to terminal 2 of the cooling fan connector, and connect the battery negative terminal to terminal 1 of the No. 2 cooling fan motor connector.
|
| ||||
| OK | |
| 5.CHECK COOLING FAN ECU (POWER SOURCE) |
![]() |
Disconnect the cooling fan ECU connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A9-3 (+B1) - A9-1 (E1) | Ignition switch on (IG) | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND) |
![]() |
Disconnect the cooling fan ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A9-1 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 7.INSPECT FAN MAIN RELAY |
![]() |
Remove the FAN MAIN relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | Battery voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Apply battery voltage between terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - FAN MAIN RELAY) |
![]() |
Disconnect the cooling fan ECU connector.
Remove the FAN MAIN relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A9-3 (+B1) - 5 (FAN MAIN relay) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - BODY GROUND) |
![]() |
Remove the FAN MAIN relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (FAN MAIN relay) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - FAN MAIN FUSE) |
![]() |
Remove the FAN MAIN relay from the engine room relay block and junction block.
Remove the fusible link block assembly from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (FAN MAIN relay) - 1 (FAN MAIN fuse) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 11.INSPECT FUSIBLE LINK BLOCK ASSEMBLY (FAN MAIN FUSE) |
![]() |
Remove the fusible link block assembly from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 (FAN MAIN fuse) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 12.CHECK FUSE (EFI MAIN) |
![]() |
Remove the EFI MAIN fuse from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI MAIN fuse | Always | Below 1 Ω |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (EFI MAIN FUSE - ENGINE ROOM JUNCTION BLOCK ASSEMBLY) |
Remove the EFI MAIN fuse from the engine room relay block and junction block.
![]() |
Remove the engine room junction block assembly from the engine room relay block and junction block.
![]() |
Disconnect the 2E connector from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (EFI MAIN fuse) - 2E-12 | Always | Below 1 Ω |
|
| ||||
| OK | |
| 14.CHECK HARNESS AND CONNECTOR (FAN MAIN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY) |
Remove the FAN MAIN relay from the engine room relay block and junction block.
![]() |
Remove the engine room junction block assembly from the engine room relay block and junction block.
![]() |
Disconnect the 2E connector from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (FAN MAIN reray) - 2E-7 | Always | Below 1 Ω |
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND) |
![]() |
Remove the engine room junction block assembly from the engine room relay block and junction block.
![]() |
Disconnect the 2D and 2E connectors from the engine room junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2D-8 - Body ground | Always | Below 1 Ω |
| 2E-10 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 16.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK ASSEMBLY) |
Disconnect the D31 connector from the ECM.
![]() |
Remove the engine room junction block assembly from the engine room relay block and junction block.
Disconnect the 2E connector from the engine room junction block assembly.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D31-8 (MREL) - 2E-9 | Always | Below 1 Ω |
|
| ||||
| OK | |
| 17.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (EFI RELAY) |
![]() |
Remove the engine room junction block assembly from the engine room relay block and junction block.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2E-12 - 2E-7 | Battery voltage is not applied between terminals 2E-9 and 2E-10 | 10 kΩ or higher |
| 2E-12 - 2E-7 | Apply battery voltage between terminals 2E-9 and 2E-10 | Below 1 Ω |
|
| ||||
| OK | ||
| ||