Home › ENGINE › 2GR-FE STARTING › SMART KEY SYSTEM

DTC    B2284    Brake Signal Malfunction

for Preparation Click here


DESCRIPTION

HINT:
When the main body ECU (instrument panel junction block) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block) is replaced, perform the registration procedures for the engine immobiliser system (Click here).


DTC No.
DTC Detection Condition
Trouble Area
B2284
The brake signal circuit between the main body ECU (instrument panel junction block) and the stop light switch is malfunctioning and the CAN information is inconsistent
  1. Stop light switch
  2. CAN communication system
  3. ECM
  4. Main body ECU (instrument panel junction block)
  5. Wire harness or connector

WIRING DIAGRAM


B177115E01


INSPECTION PROCEDURE


EMERGENCY ENGINE START CONTROL
  1. If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU (instrument panel junction block). This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
    To activate the starter:

    1. Turn the engine switch from off to on (ACC).

    2. Press and hold the engine switch for 15 seconds.

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
  1. Delete the DTCs (Click here).

  1. Check for CAN communication system DTCs (Click here).

    HINT:
    If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (Click here).

    OK:
    DTCs for CAN communication system No DTC is output.



NG
GO TO CAN COMMUNICATION SYSTEM (Click here)
OK


2.CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Check for DTCs again.

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    No DTC is output
    A
    Engine control system DTC are output
    B
    Vehicle stability control system DTC are output
    C



B
GO TO ENGINE CONTROL SYSTEM (Click here)

C
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A


3.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Check the DATA LIST for proper functioning of the stop light switch.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.



NG
Go to step 4
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

4.CHECK OPERATION OF STOP LIGHT
  1. Check whether the stop lights turn on and off normally when the brake pedal is depressed and released.

    OK:
    Stop lights turn on when brake pedal is depressed.



NG
Go to step 5
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK 

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - INSTRUMENT PANEL JUNCTION BLOCK)


  1. Disconnect the 1M connector from the instrument panel junction block.


    B176797E01

  1. Remove the stop light control relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    IM-7 - Engine room relay block stop light control relay terminal 3
    Always
    Below 1 Ω
    IM-7 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK