Home › BODY ELECTRICAL › DOOR LOCK › SMART KEY SYSTEM

SMART KEY SYSTEM > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use the following procedures to troubleshoot the smart key system.
  2. Techstream can be used in steps 4, 5, 6 and 8.
  3. When troubleshooting the smart key system using Techstream with the engine switch off, connect Techstream to the vehicle and repeat turning any of the courtesy light switches on and off until communication between the tester and the vehicle begins (the interval between ON and OFF should be less than 1.5 sec.).



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS CHECK

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points in the problem analysis:

      What
      Vehicle model, system name
      When
      Date, time, occurrence frequency
      Where
      Road conditions
      Under what conditions?
      Driving conditions, weather conditions
      How did it happen?
      Problem symptoms


    NEXT


    3.INSPECT BATTERY VOLTAGE
    1. Measure the battery voltage.

      Standard voltage:
      11 to 14 V

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


    NEXT


    4.INSPECT CAN COMMUNICATION SYSTEM
    1. Use Techstream to check if the CAN communication system is functioning normally.

      Result:

      Result
      Proceed to
      (ECU connected, communication line malfunctioning) DTC is not output.
      A
      (ECU connected, communication line malfunctioning) DTC is output.
      B
      (Click here)



    B.
    GO TO CAN COMMUNICATION SYSTEM
    A


    5.INSPECT LIN COMMUNICATION SYSTEM
    1. Use Techstream to check if the LIN communication system is functioning normally.

      Result:

      Result
      Proceed to
      (ECU connected, communication line malfunctioning) DTC is not output.
      A
      (ECU connected, communication line malfunctioning) DTC is output.
      B
      (Click here)



    A.
    GO TO LIN COMMUNICATION SYSTEM
    B


    6.CHECK FOR DTC
    1. Check for DTCs. Based on the DTCs output, try to cause the same steering lock system DTC, engine immobiliser system DTC, wireless door lock control system DTC or smart key system (starting) DTC to be output by simulating the symptoms indicated by the DTCs.

      Result:

      Result
      Proceed to
      Steering lock system DTC is not output.
      A
      (Click here)
      Engine immobiliser system DTC is output.
      B
      (Click here)
      Wireless door lock control system DTC is output.
      C
      (Click here)
      Smart key system (starting) DTC is output.
      D
      (Click here)
      DTC is not output.
      E



    A.
    GO TO STEERING LOCK SYSTEM

    B.
    GO TO ENGINE IMMOBILISER SYSTEM

    C.
    GO TO WIRELESS DOOR LOCK CONTROL SYSTEM

    D.
    GO TO SMART KEY SYSTEM (STARTING)
    E


    7.PROBLEM SYMPTOMS TABLE

      Result:

      Result
      Proceed to
      Fault is not listed in problem symptoms table.
      A
      Fault is listed in problem symptoms table.
      B



    B.
    GO TO STEP 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING
    1. OPERATION CHECK (Click here)

    2. DATA LIST/ACTIVE TEST (Click here)

    3. TERMINALS OF ECU (Click here)


    NEXT


    9.REPAIR OR REPLACE

      NEXT


      10.CONFIRMATION TEST

        NEXT

        END