Home › ENGINE › 2GR-FE STARTING › SMART KEY SYSTEM

DTC    B2285    Steering Lock Position Signal Circuit Malfunction

for Preparation Click here


DESCRIPTION

This DTC is output when serial communication signals and LIN communication signals in the circuit between the main body ECU (instrument panel junction block) and steering lock actuator (steering lock ECU) are inconsistent.

HINT:
When the main body ECU (instrument panel junction block) is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU (instrument panel junction block) or steering lock ECU is replaced, perform the registration procedures for the engine immobiliser system (Click here).


DTC No.
DTC Detection Condition
Trouble Area
B2285
Cable and LIN information between the main body ECU (instrument panel junction block) and the steering lock ECU are inconsistent
  1. Main body ECU
  2. Steering lock ECU (instrument panel junction block)
  3. Wire harness or connector

WIRING DIAGRAM


B177530E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect Techstream to the DLC3.

  1. Check the DATA LIST for proper functioning of the steering lock function.

    HINT:
    When using Techstream with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.


    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Str Unlock SW
    Steering lock condition / ON or OFF
    ON: Steering is unlocked (Engine switch on (ACC))
    OFF: Steering is locked (Engine switch off)
    -

    OK:
    ON (steering is unlocked) and OFF (steering is locked) appear on the screen.



NG
Go to step 3
OK


2.CHECK FOR DTCS
  1. Delete the DTCs (Click here).

  1. Check for DTC B2285 (Steering lock position signal circuit malfunction), DTC B2287 (LIN communication master malfunction) and DTC B2785 (Communication malfunction between ECUs connected by LIN).

    Result:
    Display (DTC output)
    Proceed to
    "DTC B2285" only
    A
    "DTC B2287" and/or "DTC B2785"
    B
    No DTC
    C

    HINT:
    If DTC B2287 is output, perform troubleshooting for DTC B2287 first.



B
GO TO DTC CHART (Click here)

C
USE SYMPTOM METHOD TO CHECK (Click here)
A

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK) 

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STEERING LOCK ECU)


  1. Disconnect the D8, 1E and D11connectors.


    B176801E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D8-18 (SLP) - D11-4 (SLP1)
    Always
    Below 1 Ω
    1E-7 (LIN1) - D11-5 (LIN)
    Always
    Below 1 Ω
    D8-18 (SLP) or D11-4 (SLP1) - Body ground
    Always
    10 kΩ or higher
    1E-7 (LIN1) or D11-5 (LIN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK MAIN BODY ECU OPERATION
  1. After replacing the main body ECU with a normally functioning ECU (instrument panel junction block), check that the engine starts. Make sure the brake pedal is depressed and the shift position is P at this time.

  1. Check that the engine switch mode can be changed by pushing the engine switch.

    HINT:
    Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.

    OK:
    Engine starts normally.



NG
REPLACE STEERING LOCK ECU (Click here)
OK

END (MAIN BODY ECU DEFECTIVE)