PARKING BRAKE ASSEMBLY > DISASSEMBLY |
| 1. REMOVE REAR WHEEL |
| 2. REMOVE REAR AXLE SHAFT NUT (for 4WD) |
| 3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD) |
![]() |
Remove the 2 bolts and separate the rear disc brake caliper assembly.
| 4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD) |
![]() |
Remove the 2 bolts and separate the rear disc brake caliper assembly.
| 5. REMOVE REAR DISC |
![]() |
Put matchmarks on the rear disc and the axle hub.
![]() |
Release the parking brake and remove the rear disc.
| 6. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING |
![]() |
Remove the 2 No. 1 parking brake shoe return tension springs.
| 7. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY |
![]() |
Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.
| 8. REMOVE PARKING BRAKE SHOE STRUT |
![]() |
Remove the parking brake shoe strut and the parking brake shoe strut compression spring.
| 9. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY |
![]() |
Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.
| 10. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET |
![]() |
Remove the parking brake shoe adjusting screw set.
| 11. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY |
![]() |
Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.
| 12. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING |
![]() |
Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.
| 13. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER |
![]() |
Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.
| 14. REMOVE PARKING BRAKE SHOE LEVER |
![]() |
Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.
| 15. REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT |
![]() |
Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.
| 16. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD) |
![]() |
Remove the No. 1 parking brake shoe hold down spring pin.
| 17. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD) |
![]() |
Remove the No. 2 parking brake shoe hold down spring pin.
| 18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD) |
| 19. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD) |
| 20. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD) |
![]() |
Remove the No. 2 parking brake shoe hold down spring pin.
| 21. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD) |
![]() |
Remove the No. 1 parking brake shoe hold down spring pin.