Home › ENGINE › 2GR-FE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR CENTER SEAT ASSEMBLY


4. REMOVE REAR SEAT HEADREST ASSEMBLY


5. REMOVE REAR SEAT TRACK BRACKET COVER LH


    B173775
  1. Disengage the 8 claws and remove the 2 rear seat track bracket covers.



6. REMOVE REAR OUTER TRACK BRACKET COVER LH


    B173776
  1. Disengage the 4 claws and remove the rear outer track bracket cover.



7. REMOVE REAR INNER TRACK BRACKET COVER


    B173777
  1. Disengage the 4 claws and remove the rear inner track bracket cover.



8. REMOVE REAR SEAT LEG SIDE COVER LH


    B173779
  1. Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.



9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)


  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.


    B180388E01



    B174594E01
  1. Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.



  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.


    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.



  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.


    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.



10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    B173780
  1. Remove the 3 bolts on the rear side of the seat.



    B173778
  1. Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



11. REMOVE REAR SEAT HEADREST ASSEMBLY


12. REMOVE REAR SEAT TRACK BRACKET COVER RH


    B173760
  1. Disengage the 8 claws and remove the 2 rear seat track bracket covers.



13. REMOVE REAR OUTER TRACK BRACKET COVER RH


    B204931
  1. Disengage the 5 claws and remove the rear outer track bracket cover.



14. REMOVE REAR INNER TRACK BRACKET COVER


    B173761
  1. Disengage the 4 claws and remove the rear inner track bracket cover.



15. REMOVE REAR SEAT LEG SIDE COVER RH


    B173765
  1. Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.



16. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)


  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.


    B180390E01



    B173766E01
  1. Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.



  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.


    B173768E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.



  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.


    B180392E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.



17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH


    B173774
  1. Remove the 3 bolts on the rear side of the seat.



    B173764
  1. Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



18. REMOVE REAR DOOR SCUFF PLATE LH


    B173228
  1. Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.



19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173232
  1. Remove the rear door opening trim weatherstrip LH.



20. REMOVE DECK BOARD ASSEMBLY


    B173240
  1. Remove the deck board assembly.



21. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Disengage the 2 guides and remove the No. 3 deck board sub-assembly.



22. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Disengage the 2 guides and remove the No. 2 deck board sub-assembly.



23. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


24. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    B175152
  1. Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.



25. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    B173607
  1. Disengage the 2 clips and remove the rear seat side cover LH.



26. REMOVE DECK SIDE TRIM BOX LH


    B173243E01
  1. Remove the 2 deck side trim clips and clip.



  1. Remove the deck side trim box LH as shown in the illustration.


    B178554



27. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    B173608
  1. Disengage the 2 clips and remove the rear seat side cover RH.



28. REMOVE JACK CARRIER SUPPORT


29. REMOVE JACK CARRIER CUSHION


    B178550
  1. Remove the jack carrier cushion.



30. REMOVE JACK ASSEMBLY


    B173245
  1. Remove the jack assembly.



31. REMOVE JACK CARRIER ASSEMBLY


    B178548
  1. Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.



32. REMOVE DECK SIDE TRIM BOX RH


    B173247E01
  1. Remove the 2 deck side trim clips and clip.



  1. Remove the deck side trim box RH as shown in the illustration.


    B178552



33. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    B178560
  1. Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.



34. REMOVE REAR MAT


    B173249
  1. Remove the rear mat.



35. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    B178561
  1. Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.



36. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    B173679
  1. Remove the 2 nuts and the deck floor box.



37. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    B170935
  1. Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.



38. REMOVE REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    B170936
  1. Remove the bolt and disconnect the rear seat lap type belt assembly LH.



39. REMOVE REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)


40. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    B205721
  1. Remove the 4 bolts and the rear No. 2 seat assembly.



41. REMOVE REAR FLOOR FINISH PLATE


    B173609
  1. Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.



42. REMOVE DECK SIDE TRIM COVER LH


    B173595E01
  1. Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.



43. REMOVE DECK SIDE TRIM LH


    B173596
  1. Remove the bolt.



    B173623
  1. Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.



44. REMOVE SIDE TRIM COVER (w/o Rear Seat Entertainment System)


    B173597
  1. Disengage the 10 claws and remove the side trim cover LH.



45. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173680
  1. Disengage the 4 claws.



    B173681
  1. Disconnect each connector and remove the power outlet socket bezel.



46. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    B173611E01
  1. Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.



47. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.



    E151327
  1. Disengage the claw and remove the rear power point socket assembly.



48. REMOVE REAR POWER OUTLET SOCKET COVER


    E151328
  1. Disengage the 2 claws and remove the rear power outlet socket cover.



49. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Disengage the 10 claws and remove the rear deck trim cover.



50. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Disengage the 5 claws and remove the reclining remote control bezel LH.



51. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    B173598E01
  1. for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.



    B173600E01
  1. for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.



52. REMOVE NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Remove the screw and the No. 2 deck side trim hook.



53. REMOVE FRONT DECK SIDE TRIM COVER LH


    B173604E01
  1. Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.



54. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170933
  1. Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.



55. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.



  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.


    B173613



56. REMOVE REAR FLOOR SERVICE HOLE COVER


  1. Lift up the front floor carpet.



      A171920
    1. Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)



    2. A176884
    3. Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)



    A171921E01
  1. Remove the rear floor service hole cover.

  1. Disconnect the fuel pump connector.



57. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


    A172549E01
  1. Remove the tube joint clip, and pull out the fuel pump tube.

    NOTICE:
    1. Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.
    2. It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
    3. Disconnect the quick connector by hand. Do not use any tools.
    4. Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
    5. If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.



    A171922E01
  1. Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    1. Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
    2. Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).



    A171923
  1. Using SST, loosen the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.

    HINT:
    The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

  1. Remove the fuel pump gauge retainer.



    A169370E01
  1. Remove the fuel suction tube with pump and gauge.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.



58. DRAIN FUEL


59. REMOVE FRONT CENTER FLOOR COVER


    C168088
  1. Remove the 4 bolts, 2 screws, and the nut.



    C168089
  1. Disengage the 4 clips and remove the center front floor cover.



60. REMOVE TAIL EXHAUST PIPE ASSEMBLY


    A170139
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.



61. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    A170125
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.



62. REMOVE NO. 4 EXHAUST PIPE SUPPORT BRACKET


    A175687
  1. Remove the 2 bolts, and then remove the No. 4 exhaust pipe support bracket.



63. REMOVE NO. 3 FRONT FLOOR HEAT INSULATOR


    A170905
  1. Remove the 4 bolts and No. 3 front floor heat insulator.



64. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)


    C166039
  1. Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.



    C166040E01
  1. Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.



    C166041
  1. Remove the 4 bolts and 4 adjusting shims.



    C166073
  1. Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.



    C166042E01
  1. Insert SST into the transfer to prevent oil leakage.

    SST
    09325-20010  



65. REMOVE REAR WHEELS (for 4WD)


66. SEPARATE REAR SPEED SENSOR LH (for 4WD)


    C166254
  1. Remove the bolt and separate the rear speed sensor from the rear shock absorber with coil spring.



67. SEPARATE REAR SPEED SENSOR RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



68. REMOVE REAR AXLE SHAFT NUT LH (for 4WD)


69. REMOVE REAR AXLE SHAFT NUT RH (for 4WD)


70. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD)


    C165996
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



71. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



72. REMOVE REAR DISC (for 4WD LH Side)


73. REMOVE REAR DISC (for 4WD RH Side)


74. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD)


    C166348E01
  1. Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.



    C165997
  1. Remove the 4 bolts and the rear axle hub and bearing assembly.

    NOTICE:
    1. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
    2. Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.



75. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



76. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for 4WD)


    C165998
  1. Remove the bolt and the nut, and separate the No. 3 parking brake cable assembly.



77. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

HINT:
Perform the same procedure as the No. 3 parking brake cable assembly.



78. REMOVE REAR STRUT ROD ASSEMBLY LH (for 4WD)


    C165999
  1. Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.



79. REMOVE REAR STRUT ROD ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



80. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH (for 4WD)


    C166000
  1. Loosen the 2 bolts.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.



    C166001
  1. Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.



    C166002
  1. Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

    HINT:
    Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.



81. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



82. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH (for 4WD)


C166222E01
  1. Put matchmarks on the adjust cams and the rear suspension member sub-assembly.

  1. Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.

    NOTICE:
    Mark the removed parts to distinguish left from right and keep them in order for reinstallation.

    HINT:
    When removing the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.



83. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



84. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH (for 4WD)


C166223
  1. Remove the bolt, the nut, and the rear No. 1 suspension arm assembly RH from the rear suspension member sub-assembly.

    NOTICE:
    1. Since a stopper nut is used, loosen the bolt.
    2. Mark the removed parts to distinguish left from right and keep them in order for reinstallation.



85. REMOVE REAR DIFFERENTIAL FILLER PLUG (for 4WD)


    C166706
  1. Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.



86. REMOVE REAR DIFFERENTIAL DRAIN PLUG (for 4WD)


    C166707
  1. Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.



87. REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)


88. REMOVE REAR DRIVE SHAFT SNAP RING LH (for 4WD)


89. REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



90. REMOVE REAR DRIVE SHAFT SNAP RING RH (for 4WD)

HINT:
Perform the same procedure as the LH side.



91. REMOVE REAR SUSPENSION MEMBER (for 4WD)


    C166232E01
  1. Support the rear suspension member with a jack using a wooden block.

    HINT:
    Use a properly sized wooden block to keep the jack and suspension member level.



    C166224E01
  1. Remove the 4 nuts, 2 bolts and 2 rear lower suspension member stopper retainers.

  1. Lower the rear suspension member.

  1. Remove the 2 rear upper suspension member stoppers.



92. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY


    A170929E01
  1. Remove the 3 clips (A) and 7 nuts, and then remove the No. 1 fuel tank protector sub-assembly.



93. REMOVE FUEL TANK ASSEMBLY


    A170930E01
  1. Disconnect the fuel pump tube.

    1. Pinch the tab of the retainer to disengage the lock claws and pull it down as shown in the illustration.

    2. Pull out the fuel pump tube.

      NOTICE:
      1. Check if there is any dirt or mud around the connector before this operation and clean the connector if necessary.
      2. It is necessary to prevent mud or dirt from entering the quick connector. If any foreign objects enter the connector, the O-rings may seal properly.
      3. Do not use any tool in this operation.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a plastic bag.
      5. When the pipe and connector are stuck, push and pull the connector to release it and pull the connector out carefully.



    A170931E01
  1. Disconnect the fuel tank vent hose from the charcoal canister assembly.

    1. Pinch the retainer and pull out the quick connector while pushing the quick connector against the pipe to disconnect the fuel tank vent hose from the charcoal canister assembly.

      NOTICE:
      1. Remove dirt or foreign objects on the quick connector before this work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting as the fuel hose connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the connected part by covering it with a plastic bag after disconnecting the fuel tank vent hose.
      6. If the quick connector and pipe are stuck, push and pull them to release.



    A175969E01
  1. Disconnect the No. 3 fuel tank breather tube.

    1. Pinch the tube connector and then pull out the No. 3 fuel tank breather tube.

      NOTICE:
      1. Check if there is any dirt or mud around the connector before this operation and clean the connector as necessary.
      2. It is necessary to prevent mud or dirt from entering the quick connector. If any foreign objects enter the connector, the O-rings may seal properly.
      3. Do not use any tool in this operation.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a plastic bag.
      5. When the pipe and connector are stuck, push and pull the connector to release it and pull the connector out carefully.



    A175980E01
  1. Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.

  1. Set a transmission jack under the fuel tank.

  1. Remove the 4 bolts, and then remove the 2 fuel tank bands.

  1. Remove the 2 nuts.



  1. Operate the transmission jack to remove the fuel tank.


    A170934



94. REMOVE REAR FUEL TANK SIDE PLATE


    A172543
  1. Remove the rear fuel tank side plate.



95. REMOVE NO. 1 FUEL TANK CUSHION


    A172544
  1. Remove the No. 1 fuel tank cushion.



96. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY


    A170936E01
  1. Release the 2 claws, and then remove the fuel pump tube.



97. REMOVE FUEL TANK TO FILLER PIPE HOSE


    A170937
  1. Loosen the hose clamp bolt, and then remove the fuel tank to filler pipe hose.



98. REMOVE FUEL TANK VENT HOSE


    A170938E01
  1. Disconnect the fuel tank vent hose from the fuel tank over fill check valve assembly.

    1. Pinch the retainer and pull out the quick connector while pushing the quick connector against the pipe to disconnect the fuel tank vent hose from the fuel tank over fill check valve assembly.

      NOTICE:
      1. Remove dirt or foreign objects on the quick connector before this work.
      2. Do not allow any scratches or foreign objects on the parts when disconnecting as the fuel hose connector has the O-ring that seals the pipe.
      3. Perform this work by hand. Do not use any tools.
      4. Do not forcibly bend, twist or turn the nylon tube.
      5. Protect the connected part by covering it with a plastic bag after disconnecting the fuel tank vent hose.
      6. If the quick connector and pipe are stuck, push and pull them to release.



    A170939E01
  1. Disconnect the No. 1 evaporation vent tube.

    NOTICE:
    1. Check if there is any dirt or mud around the connector before this operation and clean the connector as necessary.
    2. It is necessary to prevent mud or dirt from entering the quick connector. If any foreign objects enter the connector, the O-rings may seal properly.
    3. Do not use any tool in this operation.
    4. Do not bend or twist the nylon tube. Protect the connector by covering it with a plastic bag.
    5. When the pipe and connector are stuck, push and pull the connector to release it and pull the connector out carefully.



99. REMOVE FUEL TANK OVER FILL CHECK VALVE ASSEMBLY


    A170940E01
  1. Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    1. Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
    2. Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).



    A170945E01
  1. Using SST, loosen the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    NOTICE:
    Loosen the retainer by turning it counterclockwise while holding the SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.

    HINT:
    The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

  1. Remove the fuel pump gauge retainer.



    A170946
  1. Remove the fuel tank over fill check valve assembly.



    A170944
  1. Remove the tank suction tube support and gasket from the fuel tank.



100. REMOVE TANK SUCTION TUBE SUPPORT


    A170943
  1. Remove the tank suction tube support from the fuel tank.



101. REMOVE FUEL TANK SIDE PLATE


    A170942E01
  1. Remove the bolt and nut, and then remove the fuel tank side plate and the fuel tank bracket.



102. REMOVE FUEL TANK CUSHION SET


    A170941E01
  1. Remove the fuel tank cushion sets and No. 5 fuel tank cushions.