Home › TRANSMISSION ยท U151E AUTOMATIC TRANSAXLE › PARK / NEUTRAL POSITION SWITCH

PARK / NEUTRAL POSITION SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C099454
  1. Install the park/neutral position switch to the manual valve shaft.

  1. Temporarily install the 2 bolts.



    G025453
  1. Place a new lock plate and tighten the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever.



    C133989E01
  1. Turn the lever counterclockwise until it stops and then turn it clockwise 2 notches.

  1. Remove the control shaft lever.



    C099456E03
  1. Align the groove with the neutral basic line.

  1. Hold the switch in position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C161138
  1. Using a screwdriver, bend the tabs of the lock plate.



    C133985
  1. Install the control shaft lever washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



    C173673
  1. Connect the park/neutral position switch connector.



2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C133984
  1. Connect the control cable to the control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C167670
  1. Install the control cable to the bracket with a new clip.



3. ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C099453E02
  1. Loosen the 2 bolts of the park/neutral position switch and move the shift lever to the N position.

  1. Align the groove with the neutral basic line.

  1. Hold the switch in position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. After adjustment, inspect the park/neutral position switch assembly operation (Click here).



4. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to N.



    C135725E04
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.

  1. Push the lock piece into the adjuster case.

    NOTICE:
    Firmly push in the lock piece until the slider locks.

  1. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.



5. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION
  1. Apply the parking brake and turn the ignition switch to ON.

  1. Depress the brake pedal and check that the engine starts when the shift lever is set in the N position or P position, but does not start with the shift lever in the other positions.

  1. Check that the back-up light illuminates when the shift lever is set in the R position, but does not function with the shift lever in the other positions.
    If a malfunction is found, check the park/neutral position switch for continuity.



6. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P position to the R position with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N position to the D position and moves rearward when shifting to the R position. If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.



7. INSTALL AIR CLEANER BRACKET


    A171820
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }



8. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A170450
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.



9. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


10. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A171941E01
  1. Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A170887
  1. Connect the 3 vacuum hoses.



    A171944
  1. Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.



11. INSTALL NO. 1 AIR CLEANER INLET


    A170454E01
  1. Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.



12. INSTALL NO. 2 AIR CLEANER INLET


    A170453
  1. Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.



13. INSTALL COOL AIR INTAKE DUCT SEAL


    A170196
  1. Install the cool air intake duct seal with the 11 clips.



14. INSTALL BATTERY


    A171858E01
  1. Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Install the positive battery terminal and nut.

  1. Connect the negative battery terminal, and tighten the nut.



15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).