Home › SECURITIES › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM (w/o Smart Key System)

DTC    B2784    Antenna Coil Open / Short

for Preparation Click here


DESCRIPTION

The transponder key coil is built into the transponder key amplifier and receives a key code signal from the transponder chip in the key. This signal is amplified by the amplifier, then it is output to the transponder key ECU assembly.

DTC No.
DTC Detection Condition
Trouble Area
B2784
Antenna coil is open/shorted
  1. Wire harness or connector
  2. Transponder key amplifier
  3. Transponder key ECU assembly

WIRING DIAGRAM


B164252E04


INSPECTION PROCEDURE

NOTICE:
If the transponder key ECU is replaced, register the key and ECU communication ID (Click here).

1.READ VALUE ON TECHSTREAM (TRANSPONDER KEY AMPLIFIER)
  1. Connect Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Body Electrical / Immobiliser / Data List.

  1. Select Antenna Coil Status in the Data List and read the tester display.

    Immobiliser (Transponder Key ECU): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Antenna Coil Status
    Transponder key amplifier coil condition/NORMAL or FAIL
    NORMAL: Antenna coil is normal
    FAIL: Antenna coil is malfunctioning
    -

    OK:
    NORMAL (Antenna coil is normal) appears on the screen.



NG
Go to step 2
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - TRANSPONDER KEY AMPLIFIER)


    B151012E04
  1. Disconnect the transponder key ECU and transponder key amplifier connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-4 (TXCT) - D27-5 (TXCT)
    Always
    Below 1 Ω
    D41-5 (AGND) - D27-7 (AGND)
    Always
    Below 1 Ω
    D41-14 (VC5) - D27-1 (VC5)
    Always
    Below 1 Ω
    D41-15 (CODE) - D27-4 (CODE)
    Always
    Below 1 Ω
    D41-4 (TXCT) - Body ground
    Always
    10 kΩ or higher
    D41-5 (AGND) - Body ground
    Always
    10 kΩ or higher
    D41-14 (VC5) - Body ground
    Always
    10 kΩ or higher
    D41-15 (CODE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TRANSPONDER KEY AMPLIFIER POWER SOURCE)


    B128338E21
  1. Reconnect the transponder key ECU and transponder key amplifier connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D41-14 (VC5) - Body ground
    No key is in ignition key cylinder
    Below 1 V
    D41-14 (VC5) - Body ground
    Key is in ignition key cylinder
    4.6 to 5.4 V



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)
OK


4.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TRANSPONDER KEY AMPLIFIER GROUND)


    B128338E22
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D41-5 (AGND) - Body ground
    Always
    Below 1 Ω



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)
OK

REPLACE TRANSPONDER KEY AMPLIFIER (Click here)