Home › SUSPENSION & AXLE › AXLE › FRONT AXLE HUB

FRONT AXLE HUB > INSTALLATION

for Preparation Click here



1. INSTALL FRONT AXLE HUB BEARING


    C167714E03
  1. Using SST and a press, install a new front axle hub bearing to the steering knuckle.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)



2. INSTALL FRONT DISC BRAKE DUST COVER


    C166273
  1. Install the front disc brake dust cover to the steering knuckle with the 4 bolts.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }



3. INSTALL FRONT AXLE HUB SUB-ASSEMBLY


    C167715E03
  1. Using SST and a press, install the front axle hub sub-assembly to the steering knuckle.

    SST
    09608-32010  
    09950-70010   (09951-07100)
    09950-60010   (09951-00610)



4. INSTALL FRONT AXLE HUB HOLE SNAP RING


    C166270
  1. Using snap ring pliers, install a new front axle hub hole snap ring.



5. INSTALL NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR


    C166274E01
  1. Using SST and a hammer, install a new No. 1 front wheel bearing dust deflector.

    SST
    09316-60011   (09316-00011)
    09608-32010  
    09950-60020   (09951-00810, 09952-06010)
    09950-60010   (09951-00500)

    HINT:
    Align the hole for the speed sensor in the No. 1 front wheel bearing dust deflector with the steering knuckle.



6. INSTALL FRONT LOWER BALL JOINT


    C165931
  1. Install the front lower ball joint to the steering knuckle with the nut.

    Torque:
    123 N*m{ 1254 kgf*cm , 91 ft.*lbf }

    NOTICE:
    Prevent oil from adhering to the screw and tapered parts.

  1. Install a new cotter pin.

    NOTICE:
    If the holes for the cotter pin are not aligned, tighten the nut further up to 60°.



7. INSTALL FRONT AXLE ASSEMBLY


    C166269E01
  1. Install the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }



8. INSTALL FRONT DRIVE SHAFT ASSEMBLY


    C165537E05
  1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.



9. INSTALL FRONT LOWER SUSPENSION ARM


    C165929
  1. Install the front lower suspension arm to the front lower ball joint with the bolt and 2 nuts.

    Torque:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }



10. CONNECT TIE ROD ASSEMBLY
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



11. INSTALL FRONT DISC


    C165879E01
  1. Align the matchmarks and install the front disc.

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has minimal runout.



12. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY


    C165913
  1. Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    104 N*m{ 1060 kgf*cm , 76 ft.*lbf }

    NOTICE:
    Do not twist the brake hose when installing the front disc brake caliper assembly.



13. INSTALL FRONT AXLE HUB NUT
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

    HINT:
    1. Keep depressing the brake pedal to prevent the drive shaft from rotating.
    2. Stake the nut after inspecting for looseness and runout in the following steps.



14. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



15. REMOVE FRONT DISC


    C165879E01
  1. Remove the front disc.

    HINT:
    Put matchmarks on the disc and the axle hub.



16. INSPECT FRONT AXLE HUB BEARING LOOSENESS


    C166267
  1. Using a dial indicator, check for looseness near the center of the front axle hub.

    Maximum looseness:
    0 mm (0 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the looseness exceeds the maximum, replace the front axle hub bearing.



17. INSPECT FRONT AXLE HUB RUNOUT


    C166268
  1. Using a dial indicator, check for runout on the surface of the axle hub outside the hub bolt.

    Maximum runout:
    0.05 mm (0.0020 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the runout exceeds the maximum, replace the front axle hub.



18. INSTALL FRONT DISC


    C165879E01
  1. Align the matchmarks and install the front disc.

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has minimal runout.



19. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    104 N*m{ 1060 kgf*cm , 76 ft.*lbf }

    NOTICE:
    Do not twist the brake hose when installing the front disc brake caliper assembly.



20. INSTALL FRONT SPEED SENSOR


    C165818E03
  1. Install the resin clamp and front speed sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from attaching to the sensor tip.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.



21. STAKE FRONT AXLE HUB NUT


    C068609E03
  1. Using a chisel and hammer, stake the front axle hub nut.



22. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



23. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT:
Inspect and adjust the front wheel alignment (Click here).



24. CHECK FOR SPEED SENSOR SIGNAL

HINT:
Check for speed sensor signals (Click here).