VEHICLE STABILITY CONTROL SYSTEM > TEST MODE PROCEDURE |
| WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK |
Release the parking brake.
![]() |
When the ignition switch is turned on (IG), check that the ABS warning, brake warning, TRAC OFF indicator, VSC OFF indicator, slip indicator and downhill assist control indicator (for 4WD) lights come on for approximately 3 seconds.
| Trouble Area | See procedure |
| ABS warning light circuit (Remains on) |
Click here
|
| ABS warning light circuit (Does not come on) |
Click here
|
| Brake warning light circuit (Remains on) |
Click here
|
| Brake warning light circuit (Does not come on) |
Click here
|
| TRAC OFF indicator light circuit (Remains on) |
Click here
|
| TRAC OFF indicator light circuit (Does not come on) |
Click here
|
| VSC OFF indicator light circuit (Remains on) |
Click here
|
| VSC OFF indicator light circuit (Does not come on) |
Click here
|
| Slip indicator light circuit (Remains on) |
Click here
|
| Slip indicator light circuit (Does not come on) |
Click here
|
| Downhill assist control indicator light circuit (Remains on) |
Click here
|
| Downhill assist control indicator light circuit (Does not come on) |
Click here
|
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using Techstream) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in the P position.
Connect Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn Techstream on.
Switch the skid control ECU to Test Mode using Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.
![]() |
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in Test Mode.
Check the ABS sensors.
Lost Booster Pressure Judgement Check and Master Cylinder Pressure Sensor Zero Point Calibration
Turn the ignition switch on (IG).
Check that the brake warning light comes on when depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf) for 1 second or more. (The lost booster pressure state is judged as normal.)
Start the engine depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf) for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged as normal.)
Leave the vehicle for 1 second or more. (Master cylinder pressure sensor zero point calibration)
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 1 second or more.
Master Cylinder Pressure Sensor Check
Keep the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
Check the VSC sensor.
Yaw Rate Sensor Check
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
![]() |
Move the shift lever from the P position to the D position and drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.
Stop the vehicle and move the shift lever to the P position. Check that the skid control buzzer sounds for 3 seconds.
Downhill Assist Control Switch Check (for 4WD)
Push the downhill assist control switch on.
Check that the downhill assist control indicator light blinks.
Push the downhill assist control switch off.
Check that the downhill assist control indicator light goes off.
End of Sensor Check
![]() |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle is stopped and goes off while the vehicle is driving.
Read Sensor Check DTCs
Read the DTC(s) by following the tester screen.
Turn the ignition switch off and disconnect Techstream.
Sensor Check DTCs
| DTC Code | Detection Item | Trouble Area |
| C1271 | Low Output Signal of Front Speed Sensor RH |
|
| C1272 | Low Output Signal of Front Speed Sensor LH |
|
| C1273 | Low Output Signal of Rear Speed Sensor RH |
|
| C1274 | Low Output Signal of Rear Speed Sensor LH |
|
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | Speed sensor rotor |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | Speed sensor rotor |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Speed sensor rotor |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Speed sensor rotor |
| C1279 | Acceleration Sensor Output Voltage Malfunction |
|
| C1281 | Master Cylinder Pressure Sensor Output Malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| C0371 | Yaw Rate Sensor | Yaw rate and acceleration sensor |
| C1379 (*1) | Downhill Assist Control Switch Malfunction | Downhill assist control switch |
| SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using Techstream) |
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is in the straight-ahead position.
Check that the shift lever is in the P position.
![]() |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch on (IG).
![]() |
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in Test Mode.
Check the ABS sensors.
Lost Booster Pressure Judgement Check and Master Cylinder Pressure Sensor Zero Point Calibration
Turn the ignition switch on (IG).
Check that the brake warning light comes on when depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf) for 1 second or more. (The lost booster pressure state is judged as normal.)
Start the engine depressing the brake pedal with a force greater than 59 N (6 kgf, 13.2 lbf) for 1 second or more.
Check that the brake warning light goes off when quickly releasing the brake pedal. (The lost booster pressure state is judged as normal.)
Leave the vehicle for 1 second or more. (Master cylinder pressure sensor zero point calibration)
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 1 second or more.
Master Cylinder Pressure Sensor Check
Keep the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
Stop the vehicle.
Check the VSC sensor.
Yaw Rate Sensor Check
Keep the vehicle in a stationary condition on a level surface for 1 second or more.
![]() |
Move the shift lever from the P position to the D position and drive the vehicle at a speed of approximately 5 km/h (3 mph), and turn the steering wheel either to the left or right 90° or more until the vehicle makes a 180° turn.
Stop the vehicle and move the shift lever to the P position. Check that the skid control buzzer sounds for 3 seconds.
Downhill Assist Control Switch Check (for 4WD)
Push the downhill assist control switch on.
Check that the downhill assist control indicator light blinks.
Push the downhill assist control switch off.
Check that the downhill assist control indicator light goes off.
End of Sensor Check
![]() |
If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle is stopped and goes off while the vehicle is driving.
Read Sensor Check DTCs
![]() |
Using SST, connect terminals TC and CG of the DLC3.
Count the number of blinks of the ABS warning and slip indicator lights.

After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.
Turn the ignition switch on (IG).
Sensor Check DTCs
| DTC Code | Detection Item | Trouble Area |
| 71 | Low Output Signal of Front Speed Sensor RH |
|
| 72 | Low Output Signal of Front Speed Sensor LH |
|
| 73 | Low Output Signal of Rear Speed Sensor RH |
|
| 74 | Low Output Signal of Rear Speed Sensor LH |
|
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH | Speed sensor rotor |
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH | Speed sensor rotor |
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Speed sensor rotor |
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Speed sensor rotor |
| 79 | Acceleration Sensor Output Voltage Malfunction |
|
| 81 | Master Cylinder Pressure Sensor Output Malfunction |
|
| DTC Code | Detection Item | Trouble Area |
| 71 | Yaw Rate Sensor | Yaw rate and acceleration sensor |
| 74 (*1) | Downhill Assist Control Switch Malfunction | Downhill assist control switch |
| VSC OFF SWITCH CHECK |
Push the VSC OFF switch on.
Check that the TRAC OFF indicator light goes off.