Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


    C168603E01
  1. Using SST and a hammer, install a new rear differential side gear shaft oil seal until it is flush with the carrier end surface.

    SST
    09550-00032  
    09950-70010   (09951-07200)

    Oil seal driven in depth:
    0 +/- 0.5 mm (0 +/- 0.019 in.)

  1. Apply MP grease to the rear differential side gear shaft oil seal lip.



2. INSTALL REAR DRIVE SHAFT SNAP RING
  1. Install a new rear drive shaft snap ring.



3. INSTALL REAR DRIVE SHAFT ASSEMBLY


    C166347
  1. Align the shaft splines and install the rear drive shaft assembly with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening facing downward.
    2. Be careful not to damage the oil seal, boot, or dust cover.
    3. Install the drive shaft assembly while keeping it level.



4. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY


    C165999E01
  1. Check that the identification mark of the rear strut rod assembly is positioned on the inner side of the vehicle.

  1. Temporarily install the rear strut rod assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    Since stopper nuts are used, temporarily tighten the bolts.



5. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY


    C166348E01
  1. Align the matchmarks on the drive shaft and rear axle hub.

    NOTICE:
    Do not rotate the drive shaft.



    C165997
  1. Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

    Torque:
    75 N*m{ 764 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.



6. INSTALL REAR DISC


    C166438E01
  1. Align the matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    C165996
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }



8. TEMPORARILY TIGHTEN REAR AXLE SHAFT NUT


    C167784
  1. Clean the threaded parts on the rear drive shaft assembly and rear axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new rear drive shaft assembly.
    2. Keep the threaded parts free of oil and foreign objects.

  1. While applying the brakes, temporarily install a new rear axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

    NOTICE:
    Stake the nut after inspecting for looseness and runout in the following steps.



9. INSTALL REAR SPEED SENSOR


    C165809
  1. Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt .

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Keep the rear speed sensor tip and sensor installation hole free from foreign matter.
    2. Do not twist the rear speed sensor wire when installing.



10. STABILIZE SUSPENSION


    C166003E01
  1. Jack up the rear axle carrier sub-assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is positioned horizontally.

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier sub-assembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedures for the RH side and LH side.



11. FULLY TIGHTEN NO. 2 REAR SUSPENSION ARM ASSEMBLY


C166217E01
  1. Align the matchmarks on the adjust cams and rear suspension member sub-assembly.

  1. Fully tighten the nut.

    Torque:
    100 N*m{ 1019 kgf*cm , 74 ft.*lbf }

    NOTICE:
    The final torque must be applied under standard vehicle height conditions.

    HINT:
    When fully tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.

  1. Fully tighten the bolt.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



12. FULLY TIGHTEN NO. 1 REAR SUSPENSION ARM ASSEMBLY


    C166007
  1. Fully tighten the rear No. 1 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



13. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY


    C166006
  1. Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



    C166005
  1. Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.



14. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C165998
  1. Install the No. 3 parking brake cable assembly with the bolt and the nut.

    Torque:
    Bolt:
    39 N*m{ 397 kgf*cm , 29 ft.*lbf }
    Nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.



15. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY


    C165996
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.



16. REMOVE REAR DISC


    C166438E01
  1. Put matchmarks on the rear disc and the axle hub.



    D028126
  1. Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.



17. INSPECT REAR AXLE HUB BEARING LOOSENESS


    C165994
  1. Using a dial indicator, check for looseness near the center of the rear axle hub and bearing assembly.

    Maximum looseness:
    0 mm (0 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.



18. INSPECT REAR AXLE HUB RUNOUT


    C165995
  1. Using a dial indicator, check for runout on the surface of the rear axle hub and bearing assembly outside the rear axle hub bolt.

    Maximum runout:
    0.08 mm (0.0031 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.



19. INSTALL REAR DISC


    C166438E01
  1. Align the matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



20. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY


    C165996
  1. Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }



21. INSTALL REAR AXLE SHAFT NUT


    C165541
  1. Using a chisel and a hammer, stake the rear axle shaft nut.



22. INSTALL REAR DIFFERENTIAL DRAIN PLUG


    C166707
  1. Using a hexagon wrench (10 mm), install the filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



23. ADD DIFFERENTIAL OIL
  1. Fill the rear differential carrier assembly with hypoid gear oil.



24. INSPECT DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.



    C165855E01
  1. Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended oil viscosity:
    Above -18°C (0°F) : SAE 90
    Below -18°C (0°F) : SAE 80W or 80W-90
    Capacity:
    0.9 +/- 0.05 liters (0.95 +/- 0.05 US qts, 0.79 +/- 0.04 lmp. qts)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



25. INSTALL REAR DIFFERENTIAL FILLER PLUG


    C166706
  1. Using a hexagon wrench (10 mm), install the filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



26. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



27. INSPECT REAR WHEEL ALIGNMENT
(Click here)


28. CHECK REAR SPEED SENSOR SIGNAL
(Click here)