Home › STEERING › POWER STEERING › STEERING GEAR

STEERING GEAR > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



3. REMOVE COOL AIR INTAKE DUCT SEAL


    A170196
  1. Remove the 11 clips and cool air intake duct seal.



4. REMOVE BATTERY


    A171858
  1. Loosen the nut, and disconnect the negative battery terminal.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent the airbag working.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the nut, and separate the positive battery terminal cable.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



5. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


6. SECURE STEERING WHEEL


    C165552
  1. Secure the steering wheel with the seat belt in order to prevent it from rotating.

    HINT:
    This operation is necessary to prevent damage to the spiral cable.



7. REMOVE FRONT WHEELS


8. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



9. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



10. REMOVE NO. 2 ENGINE UNDER COVER


    A171854
  1. Remove the 2 bolts and No. 2 engine under cover.



11. REMOVE FLOOR UNDER COVER LH


    A171744
  1. Remove the 3 clamps, 6 bolts and front floor cover LH.



12. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH


    B172795
  1. Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.



    B172796
  1. Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly.

  1. Remove the pad from the front fender moulding sub-assembly.

  1. Remove the 2 No. 4 clips from the front fender moulding sub-assembly.



    B172797E01
  1. Remove the front fender side protector from the front fender moulding sub-assembly.



13. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side.



14. REMOVE FRONT FENDER LINER LH


    B175996E01
  1. Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.



    B174749
  1. Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



    B174751
  1. Remove the 5 clips, 8 screws and front fender liner LH.



15. REMOVE FRONT FENDER LINER RH


    B174753E01
  1. Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.



    B174750
  1. Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



    B174752
  1. Remove the 5 clips, 7 screws and front fender liner RH.



16. REMOVE FRONT FENDER APRON SEAL LH


    A171852
  1. Remove the 2 bolts, clip and front fender apron seal LH.



17. REMOVE FRONT FENDER APRON SEAL RH


    A171853
  1. Remove the 2 bolts, clip and front fender apron seal RH.



18. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and gasket, and drain the oil into a container.

  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



19. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



20. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and the gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



21. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



22. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



23. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



24. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



25. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    A173038
  1. Remove the 4 clips, and separate the engine wire.



  1. Remove the 8 bolts, 6 nuts and front outer cowl top panel sub-assembly.


    A171889



26. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



27. REMOVE NO. 2 AIR CLEANER INLET


    A170453
  1. Disconnect the 2 vacuum switching valve clamps.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.



28. REMOVE NO. 1 AIR CLEANER INLET


    A170454
  1. Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.



29. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A170887
  1. Disconnect the 3 vacuum hoses.



    A170447
  1. Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.



    A170451
  1. Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.



30. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.



31. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A170450
  1. Remove the 3 bolts, disconnect the hose and the connector, and remove the air cleaner case sub-assembly.



32. REMOVE AIR CLEANER BRACKET


    A171820
  1. Remove the 2 bolts and air cleaner bracket.



33. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    A171831
  1. Disconnect the level warning switch connector.

  1. Remove the bolt, and separate the brake master cylinder reservoir assembly.



34. REMOVE RESERVOIR BRACKET


    A171859
  1. Remove the 2 bolts and reservoir bracket.



35. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A139217
  1. Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.



36. REMOVE ENGINE MOVING CONTROL ROD


    A171824
  1. Remove the 3 bolts and engine moving control rod.



37. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE


    A171821
  1. Slide the clamp and disconnect the No. 1 fuel vapor feed hose.



38. DISCONNECT NO. 1 RADIATOR HOSE


    A171822
  1. Disconnect the clamp.

  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 radiator hose from the water outlet.



39. DISCONNECT NO. 2 RADIATOR HOSE


    A171823
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 radiator hose from the water inlet.



40. DISCONNECT HEATER WATER OUTLET HOSE B


    A171825
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect heater water outlet hose B from the water inlet.



41. DISCONNECT HEATER WATER INLET HOSE B


    A171826
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect heater water inlet hose B from the water outlet.



42. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A171827
  1. Remove the No. 1 fuel pipe clamp.



    B012941E15
  1. Disconnect the fuel tube from the fuel pipe pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for dirt and foreign objects the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.



43. DISCONNECT OIL COOLER INLET HOSE


    A171828
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 oil cooler hose.



44. DISCONNECT OIL COOLER OUTLET HOSE


    A171829
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the oil cooler outlet hose.



45. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D025414E09
  1. Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.



    C089134E03
  1. Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.



    C090579
  1. Disconnect the transmission control cable assembly from the control cable clamp.



46. DISCONNECT ENGINE WIRE


  1. Disconnect the engine wire from the engine room relay block.

    1. Remove the No. 1 relay block cover.



    2. A171851
    3. Remove the nut.

    4. Disconnect the engine wire connector from the engine room relay block.

    5. Unlock the engine wire. Pull the engine room wire.



    A173068
  1. Disconnect the engine wire clamp.



    A173069
  1. Remove the bolt, and separate the ground cables.



    A171886
  1. Disconnect the heated oxygen sensor connector and clamp.



    A173070
  1. Remove the 2 bolts, clip and 2 ground cables.



    A171880
  1. Disconnect the 3 ECM connectors, 2 junction block connectors and clamp.



    A171861
  1. Remove the 2 nuts and clamp, and separate the engine wire from the body.



47. DISCONNECT UNION TO CHECK VALVE HOSE


    A162374
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the union to check valve hose.



48. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)


    C166039
  1. Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.



    C166040E01
  1. Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.



    C166041
  1. Remove the 4 bolts and 4 adjusting shims.



    C166073
  1. Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.



    C166042E01
  1. Insert SST into the transfer to prevent oil leakage.

    SST
    09325-20010  



49. REMOVE TAIL EXHAUST PIPE ASSEMBLY


    A170139
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.



50. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    A170125
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.



51. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY


    A171743
  1. Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.



    A170126
  1. Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.



52. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A171745
  1. Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.



    A170127
  1. Loosen the bolt.

  1. Remove the 2 nuts and front exhaust pipe assembly.

  1. Remove the gasket from the front exhaust pipe assembly.



53. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C165915
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



54. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



55. REMOVE FRONT AXLE HUB NUT LH


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



56. REMOVE FRONT AXLE HUB NUT RH

HINT:
Perform the same procedure as for the LH side.



57. DISCONNECT FRONT SPEED SENSOR LH


    C165818E03
  1. Remove the bolt and resin clamp, and separate the front speed sensor.



58. DISCONNECT FRONT SPEED SENSOR RH

HINT:
Perform the same procedure as for the LH side.



59. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY


    C165544
  1. Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.



    C165545E01
  1. Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.



60. SEPARATE TIE ROD ASSEMBLY LH
  1. Remove the cotter pin and the nut.



    C165542E01
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the steering knuckle.


    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



61. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.



62. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM LH


    C165929
  1. Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.



63. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT:
Perform the same procedure as for the LH side.



64. SEPARATE FRONT AXLE ASSEMBLY LH


    C165537E04
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.



    C165534
  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Loosen the staked part of the front axle hub nut completely, otherwise the threads of the drive shaft may be damaged.



65. SEPARATE FRONT AXLE ASSEMBLY RH


66. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY


    E150345
  1. Remove the bolt and disconnect the discharge hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



67. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E150346
  1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



68. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine lifter.



    A171833
  1. Remove the 6 bolts, 2 nuts, and frame side rail plates RH and LH.



    A171834
  1. Remove the 6 bolts, 2 nuts, and front suspension member rear braces RH and LH.

  1. Operate the engine lifter, then remove the engine assembly from the vehicle.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.



69. REMOVE FRONT NO. 1 STABILIZER BRACKET LH


    C167140
  1. Remove the 2 bolts and the No. 1 front stabilizer bracket LH from the front frame assembly.



70. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.



71. REMOVE FRONT STABILIZER BAR


72. REMOVE POWER STEERING LINK ASSEMBLY


    C166343
  1. Remove the 2 bolts, 2 nuts, and power steering link assembly.

    NOTICE:
    Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed.



73. REMOVE TIE ROD ASSEMBLY LH


    C165553E01
  1. Put matchmarks on the tie rod assembly LH and the steering rack end sub-assembly.

  1. Loosen the lock nut, and remove the tie rod assembly LH and the lock nut.



74. REMOVE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.