Home › TRANSMISSION ยท U151F AUTOMATIC TRANSAXLE › TRANSMISSION CONTROL CABLE ASSEMBLY

TRANSMISSION CONTROL CABLE ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY


    C131879E01
  1. Rotate the transmission control cable nut counterclockwise and, while holding the nut in that position, press in the stopper.



    C132225E01
  1. Install the outer part of the transmission control cable assembly to the shift lever retainer.

    NOTICE:
    After installation, check that the outer part of the cable lock is protruding beyond portion A-A as shown in the illustration.



    C135727E01
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.



    C195452
  1. Install the cable end to the shift control unit.

    NOTICE:
    1. Check that the lock piece is pulled up.
    2. Install the cable end all the way to the base of the pin.
    3. Push in the lock piece after adjusting the shift lever position.



    C167674
  1. Install the transmission control cable assembly with the 3 bolts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }



    C167675E02
  1. Connect the transmission control cable assembly to the No. 2 transmission control cable bracket.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



    C133991
  1. Temporarily install the transmission control cable assembly to the control shaft lever with the nut.



    C089134
  1. Connect the transmission control cable assembly to the bracket with a new clip.



2. INSTALL AIR CONDITIONING UNIT

HINT:
(Click here)



3. INSTALL AIR CLEANER BRACKET


    A171820
  1. Install the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }



4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A170450
  1. Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.



5. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    A171941E01
  1. Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



    A170887
  1. Connect the 3 vacuum hoses.



    A171944
  1. Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.



7. INSTALL NO. 1 AIR CLEANER INLET


    A170454E01
  1. Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.



8. INSTALL NO. 2 AIR CLEANER INLET


    A170453
  1. Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.



9. INSTALL COOL AIR INTAKE DUCT SEAL


    A170196
  1. Install the cool air intake duct seal with the 11 clips.



10. INSTALL BATTERY


    A171858E01
  1. Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Install the positive battery terminal and nut.

  1. Connect the negative battery terminal, and tighten the nut.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. ADJUST SHIFT LEVER POSITION


    C135725E04
  1. Move the shift lever to N.

  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.

  1. Push the lock piece into the adjuster case.

    NOTICE:
    Firmly push in the lock piece until the slider locks.

  1. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.



13. INSPECT SHIFT LEVER POSITION
  1. When shifting from the P position to the R position with the ignition switch to ON and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.

  1. Start the engine and make sure that the vehicle moves forward when shifting from the N position to the D position and moves rearward when shifting to the R position. If the operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.