Home › BODY ELECTRICAL › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System) > No Answer-Back

for Preparation Click here


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning lights and/or wireless door lock buzzer answer-back function(s) do not operate. In such cases, the main body ECU's hazard warning lights and wireless door lock buzzer signal outputs may be malfunctioning.

NOTICE:
Troubleshooting should be started after confirming that the customize status of the answer-back function has been switched ON.


WIRING DIAGRAM


B175278E02


INSPECTION PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTION
  1. Check the wireless door lock control functions by operating the transmitter switch.

    Result:

    Result
    Proceed to
    Wireless door lock functions are normal but hazard warning lights answer-back does not occur
    A
    Wireless door lock functions are normal but wireless door lock buzzer answer-back does not occur
    B
    Doors cannot be locked and unlocked with transmitter
    C



B
Go to step 4

C
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A


2.CHECK HAZARD WARNING LIGHT
  1. Check that the hazard warning lights flash continuously when the hazard warning signal switch is pressed.

    OK:
    Hazard warning lights flash continuously.



NG
GO TO LIGHTING SYSTEM (Click here)
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (FLASHER RELAY)
  1. Select the Active Test, use Techstream to generate a control command, and then check that the hazard warning lights flash.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Hazard
    Turn Signal Flasher
    ON/OFF
    -

    OK:
    Hazard warning lights are turned ON / OFF.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

4.PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS DOOR LOCK BUZZER)
  1. Select the Active Test, use Techstream to generate a control command, and then check that the wireless buzzer operate normally.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wireless Buzzer
    Wireless Door Lock Buzzer
    ON/OFF
    -

    OK:
    Wireless buzzer turns ON/OFF.



NG
Go to step 5
OK

REPLACE MAIN BODY ECU 

5.INSPECT WIRELESS DOOR LOCK BUZZER
B170058E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    950 to 1050 Ω

    NOTICE:
    1. The buzzer circuit is built into the main body ECU, not into the buzzer itself.
    2. When battery voltage is directly applied to the buzzer, the buzzer does not sound.



NG
REPLACE WIRELESS DOOR LOCK BUZZER (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU AND BODY GROUND)

B176366E03

  1. Disconnect the A13 wireless door lock buzzer connector.

  1. Disconnect the D10 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-1 - D10-7 (BZR)
    Always
    Below 1 Ω
    A13-2 - Body ground
    Always
    A13-1 or D10-7 (BZR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU