Home › DRIVE LINE › MF2A TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.



2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



3. REMOVE COOL AIR INTAKE DUCT SEAL


    A170196
  1. Remove the 11 clips and cool air intake duct seal.



4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected .



5. REMOVE BATTERY


    A171858
  1. Loosen the nut, and disconnect the negative battery terminal.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent the airbag working.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the nut, and separate the positive battery terminal cable.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


7. REMOVE FRONT WHEELS


8. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



9. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



10. REMOVE NO. 2 ENGINE UNDER COVER


    A171854
  1. Remove the 2 bolts and No. 2 engine under cover.



11. REMOVE FLOOR UNDER COVER LH


12. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH


    B172795
  1. Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.



    B172796
  1. Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly.

  1. Remove the pad from the front fender moulding sub-assembly.

  1. Remove the 2 No. 4 clips from the front fender moulding sub-assembly.



    B172797E01
  1. Remove the front fender side protector from the front fender moulding sub-assembly.



13. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and LH side.



14. REMOVE FRONT FENDER LINER LH


    B175996E01
  1. Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.



    B174749
  1. Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



    B174751
  1. Remove the 5 clips, 8 screws and front fender liner LH.



15. REMOVE FRONT FENDER LINER RH


    B174753E01
  1. Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.



    B174750
  1. Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.



    B174752
  1. Remove the 5 clips, 7 screws and front fender liner RH.



16. REMOVE FRONT FENDER APRON SEAL LH


    A171852
  1. Remove the 2 bolts, clip and front fender apron seal LH.



17. REMOVE FRONT FENDER APRON SEAL RH


    A171853
  1. Remove the 2 bolts, clip and front fender apron seal RH.



18. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and gasket, and drain the oil into a container.

  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



19. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



20. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and the gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



21. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E150144
  1. Remove the nut, and the front wiper arm and blade assembly LH.



22. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E150145
  1. Remove the nut, and the front wiper arm and blade assembly RH.



23. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E150146
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal LH.



    E150147
  1. Disengage the 2 claws and disconnect the front fender to cowl side seal RH.



  1. Remove the 2 clips.


    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.



24. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.



25. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    A173038
  1. Remove the 4 clips, and separate the engine wire.



  1. Remove the 8 bolts, 6 nuts and front outer cowl top panel sub-assembly.


    A171889



26. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



27. REMOVE NO. 2 AIR CLEANER INLET


    A170453
  1. Disconnect the 2 vacuum switching valve clamps.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.



28. REMOVE NO. 1 AIR CLEANER INLET


    A170454
  1. Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.



29. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A170887
  1. Disconnect the 3 vacuum hoses.



    A170447
  1. Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.



    A170451
  1. Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.



30. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.



31. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A170450
  1. Remove the 3 bolts, disconnect the hose and the connector, and remove the air cleaner case sub-assembly.



32. REMOVE AIR CLEANER BRACKET


    A171820
  1. Remove the 2 bolts and air cleaner bracket.



33. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    A171831
  1. Disconnect the level warning switch connector.

  1. Remove the bolt, and separate the brake master cylinder reservoir assembly.



34. REMOVE RESERVOIR BRACKET


    A171859
  1. Remove the 2 bolts and reservoir bracket.



35. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A139217
  1. Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.



36. REMOVE ENGINE MOVING CONTROL ROD


    A171824
  1. Remove the 3 bolts and engine moving control rod.



37. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE


    A171821
  1. Slide the clamp and disconnect the No. 1 fuel vapor feed hose.



38. DISCONNECT NO. 1 RADIATOR HOSE


    A171822
  1. Disconnect the clamp.

  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 radiator hose from the water outlet.



39. DISCONNECT NO. 2 RADIATOR HOSE


    A171823
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 radiator hose from the water inlet.



40. DISCONNECT HEATER WATER OUTLET HOSE B


    A171825
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect heater water outlet hose B from the water inlet.



41. DISCONNECT HEATER WATER INLET HOSE B


    A171826
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect heater water inlet hose B from the water outlet.



42. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A171827
  1. Remove the No. 1 fuel pipe clamp.



    B012941E15
  1. Disconnect the fuel tube from the fuel pipe pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for dirt and foreign objects the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.



43. DISCONNECT OIL COOLER INLET HOSE


    A171828
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 oil cooler hose.



44. REMOVE OIL COOLER OUTLET HOSE


    A171829
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the oil cooler outlet hose.



45. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D025414E09
  1. Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.



    C089134E03
  1. Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.



    C090579
  1. Disconnect the transmission control cable assembly from the control cable clamp.



46. DISCONNECT ENGINE WIRE


  1. Disconnect the engine wire from the engine room relay block.

    1. Remove the No. 1 relay block cover.



    2. A171851
    3. Remove the nut.

    4. Disconnect the engine wire connector from the engine room relay block.

    5. Unlock the engine wire. Pull the engine room wire.



    A173068
  1. Disconnect the engine wire clamp.



    A173069
  1. Remove the bolt, and separate the ground cables.



    A171886
  1. Disconnect the heated oxygen sensor connector and clamp.



    A173070
  1. Remove the 2 bolts, clip and 2 ground cables.



    A171880
  1. Disconnect the 3 ECM connectors, 2 junction block connectors and clamp.



    A171861
  1. Remove the 2 nuts and clamp, and separate the engine wire from the body.



47. DISCONNECT UNION TO CHECK VALVE HOSE


    A162374
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the union to check valve hose.



48. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)


    C166039
  1. Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.



    C166040E01
  1. Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.



    C166041
  1. Remove the 4 bolts and 4 adjusting shims.



    C166073
  1. Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.



    C166042E01
  1. Insert SST into the transfer to prevent oil leakage.

    SST
    09325-20010  



49. REMOVE TAIL EXHAUST PIPE ASSEMBLY


    A170139
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.



50. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    A170125
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.



51. REMOVE NO. 3 FRONT EXHAUST PIPE SUB-ASSEMBLY


    A171743
  1. Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.



    A170126
  1. Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.



52. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A171745
  1. Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.



    A170127
  1. Loosen the bolt.

  1. Remove the 2 nuts and front exhaust pipe assembly.

  1. Remove the gasket from the front exhaust pipe assembly.



53. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH


    C165915
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



54. DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



55. REMOVE FRONT AXLE HUB NUT LH


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



56. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedure described for the LH side.



57. DISCONNECT FRONT SPEED SENSOR LH


    C165818E03
  1. Remove the bolt and resin clamp, and separate the front speed sensor.



58. DISCONNECT FRONT SPEED SENSOR RH

HINT:
Use the same procedure described for the LH side.



59. DISCONNECT TIE ROD ASSEMBLY LH
  1. Remove the cotter pin and the nut.



    C165542E01
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the steering knuckle.


    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



60. DISCONNECT TIE ROD ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



61. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM LH


    C165929
  1. Remove the bolt, 2 nuts, and separate the front lower suspension arm from the lower ball joint.



62. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT:
Use the same procedure described for the LH side.



63. SEPARATE FRONT AXLE ASSEMBLY LH


    C165537E04
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.



    C165534
  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Loosen the staked part of the front axle hub nut completely, otherwise the threads of the drive shaft may be damaged.



64. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



65. DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C165544
  1. Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.



    C165545E01
  1. Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.



66. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY


    E150345
  1. Remove the bolt and disconnect the discharge hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



67. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E150346
  1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



68. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine lifter.



    A171833
  1. Remove the 6 bolts, 2 nuts, and frame side rail plates RH and LH.



    A171834
  1. Remove the 6 bolts, 2 nuts, and front suspension member rear braces RH and LH.

  1. Operate the engine lifter, then remove the engine assembly from the vehicle.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.



69. REMOVE V-RIBBED BELT


    A162386E01
  1. Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.

    SST
    09961-00950  



    A095070
  1. While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.



70. REMOVE FRONT STABILIZER BAR (for 4WD)

HINT:
Click here.



71. REMOVE POWER STEERING LINK ASSEMBLY (for 4WD)


    C166343
  1. Remove the 2 bolts, 2 nuts, and power steering link assembly.

    NOTICE:
    Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed.



72. REMOVE COOLER COMPRESSOR ASSEMBLY


    E150347
  1. Disengage the clamp.

  1. Disconnect the connector.



    A176454
  1. Disengage each clamp.



    E151053
  1. Remove the 4 bolts and the compressor and magnetic clutch.



73. REMOVE VENTILATION HOSE


    A162372
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to remove the ventilation hose.



74. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A162264E01
  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly (*1).

  1. Disconnect the vapor feed hose (*2).

  1. Disconnect the throttle with motor body assembly connector and clamp (*3).

  1. Disconnect the No. 1 ventilation hose.



    A162265
  1. Disconnect the connector.

  1. Remove the 4 bolts, No. 1 surge tank stay and throttle body bracket.



    A162266E01
  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts (*4).

  1. Remove the 2 nuts and intake air surge tank (*5).

  1. Remove the gasket from the intake air surge tank.



75. REMOVE ENGINE WIRE


    A171892
  1. Disconnect the oil pressure switch cover and clamp.



    A171891
  1. Disconnect the oil pressure switch assembly connector.



    A171875
  1. Disconnect the crankshaft position sensor connector and clamp.



    A171863
  1. Disconnect the generator assembly connector and clamp.

  1. Remove the nut and separate the engine wire from the generator assembly.



    A171874
  1. Disconnect the purge VSV connector, air fuel ratio sensor connector and 2 clamps.



    A171876
  1. Remove the bolt.

  1. Disconnect the engine coolant temperature sensor connector, knock control sensor wire connector and 2 clamps.

  1. Disconnect the air fuel ratio sensor connector and clamp.



  1. Remove the bolt and 2 nuts.


    A171856

  1. Disconnect the 2 clamps, radio setting condenser connector, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector assembly connectors, and separate the engine wire from the cylinder head cover sub-assembly RH.



  1. Remove the 3 bolts.


    A171857

  1. Disconnect the 2 clamps, radio setting condenser connector, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector assembly connectors, and separate the engine wire from the engine assembly.



76. REMOVE STARTER ASSEMBLY


    A170648
  1. Disconnect the starter connector.

  1. Open the terminal cap, remove the nut and disconnect the starter wire.



    A170649
  1. Remove the 2 bolts and starter.



77. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET


    A171840
  1. Remove the 3 bolts and transverse engine mounting bracket.



78. REMOVE MANIFOLD STAY


    A155023
  1. Remove the bolt, nut, and manifold stay.



79. INSTALL ENGINE HANGERS


    A129635E01
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 engine hanger 12281-31120
    No. 2 engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



80. REMOVE FRONT FRAME ASSEMBLY


    A171835
  1. Disconnect the active mount VSV connector and harness clamp.



  1. Loosen the 3 nuts.


    A172971E01



  1. Remove the 5 hole plugs.


    A172972E01



  1. Remove the 9 nuts.


    A172973E01



    A171830
  1. Remove the 2 bolts and separate the engine with transaxle from the front frame assembly.



81. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY


    A171832
  1. Remove the nut and front engine mounting insulator assembly.



82. REMOVE TRANSVERSE ENGINE MOUNTING INSULATOR


    A171837
  1. Remove the nut and transverse engine mounting insulator.



83. REMOVE TRANSVERSE ENGINE MOUNTING INSULATOR


    A171839
  1. Remove the nut and transverse engine mounting insulator.



84. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C165535E01
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, or oil seal.
    2. Be careful not to drop the drive shaft assembly.



85. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as for the LH side.



86. REMOVE NO.2 TRANSMISSION CONTROL CABLE BRACKET


    G025454
  1. Remove the bolt and the transmission control cable bracket.



87. REMOVE WIRE HARNESS CLAMP


    C167668E01
  1. Remove the bolt and disconnect the wire harness.

  1. Remove the 3 bolts and 3 clamps.



88. REMOVE WIRE HARNESS


    C167669
  1. Remove the bolt and disconnect the wire harness.



89. DISCONNECT CONNECTORS


    D030864E11
  1. Disconnect the transmission wire connector.

  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the 2 speed sensor connectors.



90. REMOVE TRANSFER STIFFENER PLATE RH


    C167682
  1. Remove the 4 bolts and transfer stiffener plate RH.



91. REMOVE AUTOMATIC TRANSAXLE WITH TRANSFER


    D030471
  1. Remove the 2 bolts and bracket with the flywheel housing under cover.



    D030472
  1. Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.

    NOTICE:
    One of the 6 bolts has a different color than the other ones.



    C163047
  1. Remove the 10 bolts.

  1. Separate and remove the automatic transaxle with transfer.



92. REMOVE NO.1 TRANSFER CASE PLUG


    C082977E04
  1. Remove the No. 1 transfer case plug.

  1. Remove the No. 1 gasket from the No. 1 transfer case plug.



93. REMOVE NO.2 TRANSFER CASE PLUG
  1. Remove the No. 2 transfer case plug.

  1. Remove the No. 2 gasket from the No. 2 transfer case plug.



94. REMOVE TRANSFER DRAIN PLUG
  1. Remove the transfer drain plug and bleed the oil.

  1. Remove the drain gasket from the transfer drain plug.



95. REMOVE TRANSFER ASSEMBLY


    C082785E01
  1. Remove the 2 bolts and 6 nuts.

  1. Using a plastic hammer, remove the transfer assembly from the transaxle assembly.

    NOTICE:
    1. Remove the transfer assembly from the transaxle assembly without tilting it.
    2. When removing the transfer assembly, do not hold onto the oil seal parts on both sides of the assembly.