TRANSFER CASE OIL SEAL > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
| 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM |
Start the engine.
Turn the A/C switch on.
Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
| 3. REMOVE COOL AIR INTAKE DUCT SEAL |
![]() |
Remove the 11 clips and cool air intake duct seal.
| 4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 5. REMOVE BATTERY |
![]() |
Loosen the nut, and disconnect the negative battery terminal.
Remove the nut, and separate the positive battery terminal cable.
Loosen the nut, and remove the bolt and battery clamp.
Remove the battery and battery tray.
| 6. PLACE FRONT WHEELS FACING STRAIGHT AHEAD |
| 7. REMOVE FRONT WHEELS |
| 8. REMOVE ENGINE UNDER COVER ASSEMBLY |
![]() |
Remove the 2 bolts and engine under cover assembly RR.
![]() |
Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.
| 9. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 6 bolts, 2 clips and No. 1 engine under cover.
| 10. REMOVE NO. 2 ENGINE UNDER COVER |
![]() |
Remove the 2 bolts and No. 2 engine under cover.
| 11. REMOVE FLOOR UNDER COVER LH |
| 12. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Using a 4 mm hexagon wrench, remove the screw.
![]() |
Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly.
Remove the pad from the front fender moulding sub-assembly.
Remove the 2 No. 4 clips from the front fender moulding sub-assembly.
![]() |
Remove the front fender side protector from the front fender moulding sub-assembly.
| 13. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH |
| 14. REMOVE FRONT FENDER LINER LH |
![]() |
Remove the screw.
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Using a 4 mm hexagon wrench, remove the 2 screws.
Remove the 2 grommets.
![]() |
Remove the 5 clips, 8 screws and front fender liner LH.
| 15. REMOVE FRONT FENDER LINER RH |
![]() |
Remove the screw.
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Using a 4 mm hexagon wrench, remove the 2 screws.
Remove the 2 grommets.
![]() |
Remove the 5 clips, 7 screws and front fender liner RH.
| 16. REMOVE FRONT FENDER APRON SEAL LH |
![]() |
Remove the 2 bolts, clip and front fender apron seal LH.
| 17. REMOVE FRONT FENDER APRON SEAL RH |
![]() |
Remove the 2 bolts, clip and front fender apron seal RH.
| 18. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil drain plug and gasket, and drain the oil into a container.
Clean and install the oil drain plug with a new gasket.
| 19. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.

Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the 2 cylinder block drain cock plugs.
| 20. DRAIN AUTOMATIC TRANSAXLE FLUID |
Remove the drain plug and the gasket, and drain ATF.
Install a new gasket and the drain plug.
| 21. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Remove the nut, and the front wiper arm and blade assembly LH.
| 22. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Remove the nut, and the front wiper arm and blade assembly RH.
| 23. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and disconnect the front fender to cowl side seal LH.
![]() |
Disengage the 2 claws and disconnect the front fender to cowl side seal RH.
Remove the 2 clips.

Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.
| 24. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 4 bolts, and the windshield wiper motor and link assembly.
| 25. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY |
![]() |
Remove the 4 clips, and separate the engine wire.
Remove the 8 bolts, 6 nuts and front outer cowl top panel sub-assembly.

| 26. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the cover.
| 27. REMOVE NO. 2 AIR CLEANER INLET |
![]() |
Disconnect the 2 vacuum switching valve clamps.
Disconnect the 2 vacuum hoses.
Remove the 2 bolts and No. 2 air cleaner inlet.
| 28. REMOVE NO. 1 AIR CLEANER INLET |
![]() |
Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.
| 29. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the 3 vacuum hoses.
![]() |
Loosen the No. 1 air cleaner hose clamp.
Disconnect the hose clamps and No. 2 ventilation hose.
Disconnect the mass air flow meter connector.
![]() |
Release the 2 clips, and remove the 2 bolts.
Remove the air cleaner cap sub-assembly and air cleaner filter element.
| 30. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly.
| 31. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Remove the 3 bolts, disconnect the hose and the connector, and remove the air cleaner case sub-assembly.
| 32. REMOVE AIR CLEANER BRACKET |
![]() |
Remove the 2 bolts and air cleaner bracket.
| 33. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
![]() |
Disconnect the level warning switch connector.
Remove the bolt, and separate the brake master cylinder reservoir assembly.
| 34. REMOVE RESERVOIR BRACKET |
![]() |
Remove the 2 bolts and reservoir bracket.
| 35. REMOVE NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.
| 36. REMOVE ENGINE MOVING CONTROL ROD |
![]() |
Remove the 3 bolts and engine moving control rod.
| 37. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE |
![]() |
Slide the clamp and disconnect the No. 1 fuel vapor feed hose.
| 38. DISCONNECT NO. 1 RADIATOR HOSE |
![]() |
Disconnect the clamp.
Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 radiator hose from the water outlet.
| 39. DISCONNECT NO. 2 RADIATOR HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 radiator hose from the water inlet.
| 40. DISCONNECT HEATER WATER OUTLET HOSE B |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect heater water outlet hose B from the water inlet.
| 41. DISCONNECT HEATER WATER INLET HOSE B |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect heater water inlet hose B from the water outlet.
| 42. DISCONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Remove the No. 1 fuel pipe clamp.
![]() |
Disconnect the fuel tube from the fuel pipe pinching part A with your fingers as shown in the illustration.
| 43. DISCONNECT OIL COOLER INLET HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 oil cooler hose.
| 44. REMOVE OIL COOLER OUTLET HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the oil cooler outlet hose.
| 45. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Remove the nut from the control shaft lever.
Disconnect the transmission control cable assembly from the control shaft lever.
![]() |
Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.
![]() |
Disconnect the transmission control cable assembly from the control cable clamp.
| 46. DISCONNECT ENGINE WIRE |
Disconnect the engine wire from the engine room relay block.
Remove the No. 1 relay block cover.
![]() |
Remove the nut.
Disconnect the engine wire connector from the engine room relay block.
Unlock the engine wire. Pull the engine room wire.
![]() |
Disconnect the engine wire clamp.
![]() |
Remove the bolt, and separate the ground cables.
![]() |
Disconnect the heated oxygen sensor connector and clamp.
![]() |
Remove the 2 bolts, clip and 2 ground cables.
![]() |
Disconnect the 3 ECM connectors, 2 junction block connectors and clamp.
![]() |
Remove the 2 nuts and clamp, and separate the engine wire from the body.
| 47. DISCONNECT UNION TO CHECK VALVE HOSE |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the union to check valve hose.
| 48. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD) |
![]() |
Depress the brake pedal and hold it.
Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.
![]() |
Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.
Remove the 4 nuts, 4 bolts and 4 washers.
![]() |
Remove the 4 bolts and 4 adjusting shims.
![]() |
Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.
![]() |
Insert SST into the transfer to prevent oil leakage.
| 49. REMOVE TAIL EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.
Remove the gasket from the center exhaust pipe assembly.
| 50. REMOVE CENTER EXHAUST PIPE ASSEMBLY |
![]() |
Remove the 2 bolts and 2 compression springs.
Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.
Remove the gasket from the No. 3 exhaust pipe sub-assembly.
| 51. REMOVE NO. 3 FRONT EXHAUST PIPE SUB-ASSEMBLY |
![]() |
Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.
![]() |
Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.
Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.
| 52. REMOVE FRONT EXHAUST PIPE ASSEMBLY |
![]() |
Disconnect the heated oxygen sensor (for bank 2 sensor 2) connector.
![]() |
Loosen the bolt.
Remove the 2 nuts and front exhaust pipe assembly.
Remove the gasket from the front exhaust pipe assembly.
| 53. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Remove the nut and separate the front stabilizer link assembly from the front shock absorber.
| 54. DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH |
| 55. REMOVE FRONT AXLE HUB NUT LH |
![]() |
Using SST and a hammer, release the staked part of the front axle hub nut.
While applying the brakes, remove the front axle hub nut.
| 56. REMOVE FRONT AXLE HUB NUT RH |
| 57. DISCONNECT FRONT SPEED SENSOR LH |
![]() |
Remove the bolt and resin clamp, and separate the front speed sensor.
| 58. DISCONNECT FRONT SPEED SENSOR RH |
| 59. DISCONNECT TIE ROD ASSEMBLY LH |
Remove the cotter pin and the nut.
![]() |
Install SST to the tie rod end.
Using SST, separate the tie rod end from the steering knuckle.

| 60. DISCONNECT TIE ROD ASSEMBLY RH |
| 61. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM LH |
![]() |
Remove the bolt, 2 nuts, and separate the front lower suspension arm from the lower ball joint.
| 62. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM RH |
| 63. SEPARATE FRONT AXLE ASSEMBLY LH |
![]() |
Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.
![]() |
Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.
| 64. SEPARATE FRONT AXLE ASSEMBLY RH |
| 65. DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY |
![]() |
Remove the bolt and slide the steering intermediate shaft assembly.
![]() |
Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
Separate the steering intermediate shaft assembly from the power steering link assembly.
| 66. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY |
![]() |
Remove the bolt and disconnect the discharge hose sub-assembly from the compressor and magnetic clutch.
Remove the O-ring from the discharge hose sub-assembly.
| 67. DISCONNECT SUCTION HOSE SUB-ASSEMBLY |
![]() |
Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.
Remove the O-ring from the suction hose sub-assembly.
| 68. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE |
Set the engine lifter.
![]() |
Remove the 6 bolts, 2 nuts, and frame side rail plates RH and LH.
![]() |
Remove the 6 bolts, 2 nuts, and front suspension member rear braces RH and LH.
Operate the engine lifter, then remove the engine assembly from the vehicle.
| 69. REMOVE V-RIBBED BELT |
![]() |
Using SST, release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and remove the V-ribbed belt from the V-ribbed belt tensioner assembly.
![]() |
While turning the V-ribbed belt tensioner assembly counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner assembly.
| 70. REMOVE FRONT STABILIZER BAR (for 4WD) |
| 71. REMOVE POWER STEERING LINK ASSEMBLY (for 4WD) |
![]() |
Remove the 2 bolts, 2 nuts, and power steering link assembly.
| 72. REMOVE COOLER COMPRESSOR ASSEMBLY |
![]() |
Disengage the clamp.
Disconnect the connector.
![]() |
Disengage each clamp.
![]() |
Remove the 4 bolts and the compressor and magnetic clutch.
| 73. REMOVE VENTILATION HOSE |
![]() |
Using pliers, grip the claws of the 2 clips and slide the 2 clips to remove the ventilation hose.
| 74. REMOVE INTAKE AIR SURGE TANK ASSEMBLY |
![]() |
Disconnect the 2 water by-pass hoses from the throttle with motor body assembly (*1).
Disconnect the vapor feed hose (*2).
Disconnect the throttle with motor body assembly connector and clamp (*3).
Disconnect the No. 1 ventilation hose.
![]() |
Disconnect the connector.
Remove the 4 bolts, No. 1 surge tank stay and throttle body bracket.
![]() |
Using a 5 mm socket hexagon wrench, remove the 4 bolts (*4).
Remove the 2 nuts and intake air surge tank (*5).
Remove the gasket from the intake air surge tank.
| 75. REMOVE ENGINE WIRE |
![]() |
Disconnect the oil pressure switch cover and clamp.
![]() |
Disconnect the oil pressure switch assembly connector.
![]() |
Disconnect the crankshaft position sensor connector and clamp.
![]() |
Disconnect the generator assembly connector and clamp.
Remove the nut and separate the engine wire from the generator assembly.
![]() |
Disconnect the purge VSV connector, air fuel ratio sensor connector and 2 clamps.
![]() |
Remove the bolt.
Disconnect the engine coolant temperature sensor connector, knock control sensor wire connector and 2 clamps.
Disconnect the air fuel ratio sensor connector and clamp.
Remove the bolt and 2 nuts.

Disconnect the 2 clamps, radio setting condenser connector, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector assembly connectors, and separate the engine wire from the cylinder head cover sub-assembly RH.
Remove the 3 bolts.

Disconnect the 2 clamps, radio setting condenser connector, 3 ignition coil assembly connectors, 2 camshaft timing oil control valve assembly connectors, 2 VVT sensor connectors and 3 injector assembly connectors, and separate the engine wire from the engine assembly.
| 76. REMOVE STARTER ASSEMBLY |
![]() |
Disconnect the starter connector.
Open the terminal cap, remove the nut and disconnect the starter wire.
![]() |
Remove the 2 bolts and starter.
| 77. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET |
![]() |
Remove the 3 bolts and transverse engine mounting bracket.
| 78. REMOVE MANIFOLD STAY |
![]() |
Remove the bolt, nut, and manifold stay.
| 79. INSTALL ENGINE HANGERS |
![]() |
Install the 2 engine hangers with the 4 bolts as shown in the illustration.
Attach the engine sling device and hang the engine with the chain block.
| 80. REMOVE FRONT FRAME ASSEMBLY |
![]() |
Disconnect the active mount VSV connector and harness clamp.
Loosen the 3 nuts.

Remove the 5 hole plugs.

Remove the 9 nuts.

![]() |
Remove the 2 bolts and separate the engine with transaxle from the front frame assembly.
| 81. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY |
![]() |
Remove the nut and front engine mounting insulator assembly.
| 82. REMOVE TRANSVERSE ENGINE MOUNTING INSULATOR |
![]() |
Remove the nut and transverse engine mounting insulator.
| 83. REMOVE TRANSVERSE ENGINE MOUNTING INSULATOR |
![]() |
Remove the nut and transverse engine mounting insulator.
| 84. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Using SST, remove the front drive shaft assembly LH.
| 85. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD) |
| 86. REMOVE WIRE HARNESS CLAMP |
![]() |
Remove the bolt and disconnect the wire harness.
Remove the 3 bolts and 3 clamps.
| 87. DISCONNECT WIRE HARNESS |
![]() |
Remove the bolt and disconnect the wire harness.
| 88. DISCONNECT CONNECTORS |
![]() |
Disconnect the transmission wire connector.
Disconnect the park/neutral position switch connector.
Disconnect the 2 speed sensor connectors.
| 89. REMOVE TRANSFER STIFFENER PLATE RH |
![]() |
Remove the 4 bolts and transfer stiffener plate RH.
| 90. REMOVE AUTOMATIC TRANSAXLE WITH TRANSFER |
![]() |
Remove the 2 bolts and bracket with the flywheel housing under cover.
![]() |
Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.
![]() |
Remove the 10 bolts.
Separate and remove the automatic transaxle with transfer.
| 91. REMOVE NO.1 TRANSFER CASE PLUG |
![]() |
Remove the No. 1 transfer case plug.
Remove the No. 1 gasket from the No. 1 transfer case plug.
| 92. REMOVE NO.2 TRANSFER CASE PLUG |
Remove the No. 2 transfer case plug.
Remove the No. 2 gasket from the No. 2 transfer case plug.
| 93. REMOVE TRANSFER DRAIN PLUG |
Remove the transfer drain plug and bleed the oil.
Remove the drain gasket from the transfer drain plug.
| 94. REMOVE TRANSFER ASSEMBLY |
![]() |
Remove the 2 bolts and 6 nuts.
Using a plastic hammer, remove the transfer assembly from the transaxle assembly.
| 95. REMOVE CTR DIFFERENTIAL LOCK SLEEVE |
![]() |
Using snap ring pliers, remove the shaft snap ring.
![]() |
Using SST, remove the CTR differential lock sleeve.
| 96. REMOVE TRANSFER CASE OIL SEAL |
![]() |
Using SST, remove the transfer case oil seal from the transfer case.