DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0057 Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2) |
DTC P0058 Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2) |
DTC P0141 Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0161 Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 P0057 | Heated oxygen sensor heater current is less than 0.3 A (1 trip detection logic) |
|
| P0038 P0058 | Heated oxygen sensor heater current is more than 2 A (1 trip detection logic) |
|
| P0141 P0161 | Cumulative heater resistance correction value exceeds the acceptable threshold (2 trip detection logic) |
|
| Related DTCs | P0037: Heated oxygen sensor heater (bank 1) open/short (Low electrical current) P0038: Heated oxygen sensor heater (bank 1) open/short (High electrical current) P0057: Heated oxygen sensor heater (bank 2) open/short (Low electrical current) P0058: Heated oxygen sensor heater (bank 2) open/short (High electrical current) P0141: Heated oxygen sensor heater performance (bank 1 sensor 2) P0161: Heated oxygen sensor heater performance (bank 2 sensor 2) |
| Required Sensors / Components (Main) | Heated oxygen sensor heater (bank 1 and 2) |
| Required Sensors / Components (Related) | Vehicle speed sensor |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P0037 and P0057 1 second: P0038 and P0058 10 seconds: P0141 and P0161 |
| MIL Operation | Immediate: P0037, P0038, P0057 and P0058 2 driving cycles: P0141 and P0161 |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Battery voltage | 10.5 to 20 V |
| Battery voltage | 10.5 V or more |
| Engine | Running |
| Starter | OFF |
| One of the following conditions is met: | Condition A or B |
| A. All of the following conditions are met: | Conditions 1, 2, 3, 4 and 5 |
| 1. Battery voltage | 10.5 V or more |
| 2. Fuel cut | OFF |
| 3. Time after fuel cut ON to OFF | 30 seconds or more |
| 4. Accumulated heater ON time | 100 seconds or more |
| 5. Learned heater OFF current operation | Completed |
| B. Duration that rear heated oxygen sensor impedance is less than 15 kΩ | 2 seconds or more |
| Heater Current - Learned heater OFF current | Less than 0.3 A |
| Learned heater OFF current | More than 2 A |
| Heater Current - Learned heater OFF current | 2 A or more |
| Accumulated heater resistance | Varies with sensor element temperature (Example: More than 23 Ω) |
| Heated oxygen sensor heater current | 0.3 to 2 A (when engine idles, heated oxygen sensor warmed up and battery voltage 11 to 14 V) |
| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (HT1B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT1B) - 4 (E2) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E2) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B TERMINAL OF HEATED OXYGEN SENSOR) |
![]() |
Disconnect the heated oxygen sensor connector.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-2 (+B) - Body ground | Ignition switch on (IG) | 9 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| B39-2 (+B) - Body ground | Ignition switch on (IG) | 9 to 14 V |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
![]() |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P1-1 (HT1B) - B1-1 (HT1B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B39-1 (HT2B) - B2-5 (HT2B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| P1-1 (HT1B) or B1-1 (HT1B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B39-1 (HT2B) or B2-5 (HT2B) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connectors.
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0037, P0038, P0057, P0058, P0141 and/or P0161 | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT FUSE (EFI NO. 3 FUSE) |
![]() |
Remove the EFI No. 3 fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI No. 3 fuse | Always | Below 1 Ω |
Reinstall the EFI No. 3 fuse.
|
| ||||
| OK | ||
| ||