DTC P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0015 Camshaft Position "B" - Timing Over-Retarded (Bank 1) |
DTC P0024 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 2) |
DTC P0025 Camshaft Position "B" - Timing Over-Retarded (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0014 P0024 | Valve timing is not adjusted in valve timing advance range (2 trip detection logic) |
|
| P0015 P0025 | Valve timing is not adjusted in valve timing retard range (1 trip detection logic) |
|
| Related DTCs | P0014: Advanced exhaust camshaft timing (bank 1) P0015: Retarded exhaust camshaft timing (bank 1) P0024: Advanced exhaust camshaft timing (bank 2) P0025: Retarded exhaust camshaft timing (bank 2) |
| Required Sensors / Components (Main) | VVT camshaft timing oil control valve and VVT Actuator |
| Required Sensors / Components (Related) | P0014 and P0015: Exhaust camshaft control actuator bank 1 Exhaust camshaft timing oil control valve bank 1 P0024 and P0025: Exhaust camshaft control actuator bank 2 Exhaust camshaft timing oil control valve bank 2 |
| Frequency of Operation | Continuously |
| Duration | Less than 10 seconds |
| MIL Operation | P0014 and P0024: 2 driving cycles P0015 and P0025: Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0013, P0023 (Exhaust OCV bank 1, 2) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0100, P0102, P0103 (MAF meter) P0115, P0117, P0118 (ECT sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) |
| Battery voltage | 11 V or more |
| Engine RPM | 500 to 4000 rpm |
| Engine coolant temperature | 75 to 100°C (167 to 212°F) |
| Valve timing | No change |
| Valve timing | Advanced position |
| Valve timing | No change |
| Valve timing | Retarded position |
| Abnormal bank | Advanced timing over (Valve timing is out of specified range) | Retarded timing over (Valve timing is out of specified range) |
| Bank 1 | P0014 | P0015 |
| Bank 2 | P0024 | P0025 |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014, P0015, P0024 OR P0025) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0014, P0015, P0024 or P0025 | A |
| P0014, P0015, P0024 or P0025 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OIL CONTROL VALVE FOR EXHAUST CAMSHAFT) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the oil control valve using the tester.
| Tester Operation | Specified Condition |
| -128% (Oil control valve OFF) | Normal engine idle speed |
| 127% (Oil control valve ON) | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014, P0015, P0024 OR P0025) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read the DTCs using the tester.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMP TEETH ON TIMING CHAIN) |
![]() |
Remove the cylinder head covers RH and LH.
Turn the crankshaft to align the matchmarks of the crankshaft.
Align the notch of the crankshaft pulley to the "0" position.
Check if the matchmarks of the camshaft pulley and camshaft bearing cap align.
Turn the crankshaft clockwise by 360° if the matchmarks do not align. Check if they align once again.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Remove the exhaust camshaft timing oil control valve.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
![]() |
Apply the positive battery voltage to terminal 1 and the negative battery voltage to terminal 2. Check the valve operation.
Reinstall the camshaft timing oil control valve.
|
| ||||
| OK | |
| 6.CHECK OIL PIPE AND OIL CONTROL VALVE FILTER |
![]() |
Remove the oil pipe No. 1 or oil pipe assembly.
Remove the oil control valve filter.
Check that the filter and pipe are not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Confirm that no DTC is set using the tester.
|
| ||||
| OK | ||
| ||