DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to ECM for 20 seconds (1 trip detection logic): (a) Vehicle speed more than 12.4 mph (20 km/h) (b) Engine speed more than 1000 rpm (c) STA signal ON |
|
| Related DTCs | P0617: Starter signal |
| Required Sensors / Components (Main) | STARTER relay, Park/neutral position switch, Clutch start switch and Ignition switch |
| Required Sensors / Components (Related) | Vehicle Speed Sensor (VSS), Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 20 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | None |
| Battery voltage | 10.5 V or more |
| Vehicle speed | 12.43 mph (20 km/h) or more |
| Engine speed | 1000 rpm or more |
| Starter signal | ON |


| 1.CHECK IF VEHICLE IS EQUIPPED WITH SMART KEY SYSTEM |
| Result | Proceed to |
| w/o Smart Key System | A |
| w/ Smart Key System | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
| Ignition Switch Condition | Tester Display (Starter Signal) |
| On (IG) | OFF |
| Engine Starts | ON |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| P | 4 - 5 | Below 1 Ω |
| N | 4 - 5 |
| Result | Proceed to |
| NG | A |
| OK | B |
Reconnect the park/neutral position switch connector.
|
| ||||
| A | |
| 4.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park/neutral position switch (U151E: Click here, U151F: Click here).
| NEXT | |
| 5.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
| Ignition Switch Condition | Tester Display (Starter Signal) |
| On (IG) | OFF |
| Engine Starts | ON |
|
| ||||
| OK | ||
| ||
| 6.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Ignition Switch Position | Tester Connection | Specified Condition |
| LOCK | All Terminals | 10 kΩ or higher |
| ACC | 2 - 3 | Below 1 Ω |
| ON | 2 - 3, 2 - 4, 6 - 7 | |
| START | 1 - 2, 2 - 4, 6 - 7, 7 - 8 |
| Result | Proceed to |
| NG | A |
| OK | B |
Reconnect the ignition switch connector.
|
| ||||
| A | |
| 7.REPLACE IGNITION OR STARTER SWITCH |
Replace the ignition switch assembly (Click here).
| NEXT | |
| 8.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
| Ignition Switch Condition | Tester Display (Starter Signal) |
| On (IG) | OFF |
| Engine Starts | ON |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 9.REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Clear DTCs (Click here).
Drive the vehicle at more than 20 km/h (12.4 mph) for over 20 seconds.
Select the following menu items: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
| P0617 | A |
| No DTC | B |
|
| ||||
| A | ||
| ||
| 11.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG) and turn the tester on.
Select the following menu items: Powertrain / Engine / Data List / Starter Signal.
Check the result when the ignition switch is turned on (IG).
Check the result when the engine starts.
| Ignition Switch Condition | Tester Display (Starter Signal) |
| On (IG) | OFF |
| Engine Starts | ON |
|
| ||||
| OK | ||
| ||
| 12.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Gear Selector Lever Position | Tester Connection | Specified Condition |
| P | 4 - 5 | Below 1 Ω |
| N | 4 - 5 |
| Result | Proceed To |
| OK | A |
| NG (with U151E)) | B |
| NG (with U151F) | C |
Reconnect the park/neutral position switch connector.
|
| ||||
|
| ||||
| A | ||
| ||