DTC B1622/81 Lost Communication with Driver Side - Side Airbag Sensor Assembly |
DTC B1623/81 Driver Side - Side Airbag Sensor Assembly Initialization Incomplete |
DTC B1632/81 Lost Communication with Driver Side Rear Airbag Sensor |
DTC B1633/81 Driver Side Rear Airbag Sensor Initialization Incomplete |
DTC B1642/81 Lost Communication with Driver Side Satellite Sensor Bus |
DTC B1643/81 Driver Side Satellite Sensor Bus Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1622/81 B1623/81 B1632/81 B1633/81 B1642/81 B1643/81 |
|
|

| 1.CHECK PRESENT DTC |
![]() |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for present DTCs (Click here).
| Result | Proceed to |
| Present DTC B1623 or B1643 is output | A |
| Present DTC B1642 or 81 is output | B |
| Present DTC B1632 or B1633 is output | C |
| Present DTC B1622 is output | D |
| Present DTC B1622, B1623, B1632, B1633, B1642, B1643 or 81 is not output | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK PAST DTC |
Check for past DTCs (Click here).
| Result | Proceed to |
| Past DTC B1622 or B1632 is not output | A |
| Past DTC B1632 is output | B |
| Past DTC B1622 is output | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly, rear airbag sensor LH and the side airbag sensor LH.
Disconnect the connectors from the center airbag sensor assembly, rear airbag sensor LH and side airbag sensor LH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE NO. 2 (OPEN) |
![]() |
Using SST, connect terminals 24 (BBD+) and 23 (BBD-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-4 (BBL+) - O3-3 (BBL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE NO. 2 (SHORT) |
![]() |
Disconnect SST from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-4 (BBL+) - O3-3 (BBL-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE NO. 2 (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-4 (BBL+) - Body ground | Ignition switch on (IG) | Below 1 V |
| O3-3 (BBL-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 7.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-4 (BBL+) - Body ground | Always | 1 MΩ or higher |
| O3-3 (BBL-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 8.CHECK FLOOR WIRE NO. 2 (OPEN) |
![]() |
Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - O3-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.CHECK FLOOR WIRE NO. 2 (SHORT) |
![]() |
Disconnect SST from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - O3-2 (BCL-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 10.CHECK FLOOR WIRE NO. 2 (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - Body ground | Ignition switch on (IG) | Below 1 V |
| O3-2 (BCL-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 11.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| O3-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 12.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Connect the connectors to the rear airbag sensor LH and center airbag sensor assembly.
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623, B1642, B1643, or 81 is output. | A |
| DTC B1628, B1647, B1648, or 82 is output. | B |
| DTCs B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 13.CHECK REAR AIRBAG SENSOR LH |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
Interchange the rear airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output. | A |
| DTC B1623, B1642, B1643, or 81 is output. | B |
| DTC B1628, B1647, B1648, or 82 is output. | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 14.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the side airbag sensor LH and rear airbag sensor LH.
Disconnect the connectors from the side airbag sensor LH and rear airbag sensor LH.
Check that the terminals of connectors are not damaged.
|
| ||||
| OK | |
| 15.CHECK FLOOR WIRE NO. 2 (OPEN) |
![]() |
Using SST, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - O3-2 (BCL-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 16.CHECK FLOOR WIRE NO. 2 (SHORT) |
![]() |
Disconnect SST from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - O3-2 (BCL-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 17.CHECK FLOOR WIRE NO. 2 (SHORT TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - Body ground | Ignition switch on (IG) | Below 1 V |
| O3-2 (BCL-) - Body ground | Ignition switch on (IG) | Below 1 V |
|
| ||||
| OK | |
| 18.CHECK FLOOR WIRE NO. 2 (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O3-1 (BCL+) - Body ground | Always | 1 MΩ or higher |
| O3-2 (BCL-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 19.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Connect the connector to the rear airbag sensor LH.
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1632 or B1633 is output. | A |
| DTC B1637 or B1638 is output. | B |
| DTC B1632 or B1633 and B1637 or B1638 are not output. | C |
|
| ||||
|
| ||||
| A | |
| 20.CHECK REAR AIRBAG SENSOR LH |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.
Interchange the rear airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1632 or B1633 and B1637 or B1638 are not output. | A |
| DTC B1632 or B1633 is output. | B |
| DTC B1637 or B1638 is output. | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 21.CHECK SIDE AIRBAG SENSOR LH |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Interchange the side airbag sensor RH with LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1622 and B1627 are not output. | A |
| DTC B1622 is output. | B |
| DTC B1627 is output. | C |
|
| ||||
|
| ||||
| A | ||
| ||