Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1627/82    Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly

DTC    B1628/82    Front Passenger Side - Side Airbag Sensor Assembly Initialization Incomplete

DTC    B1637/82    Lost Communication with Passenger Side Rear Airbag Sensor

DTC    B1638/82    Passenger Side Rear Airbag Sensor Initialization Incomplete

DTC    B1647/82    Lost Communication with Front Passenger Side Satellite Sensor Bus

DTC    B1648/82    Front Passenger Side Satellite Sensor Bus Initialization Incomplete

for Preparation Click here


DESCRIPTION

The circuit for the front passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor assembly, side airbag sensor RH, and rear airbag sensor RH.
The side airbag sensor RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.
Theses DTCs are recorded when a malfunction is detected in the circuit for the front passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

DTC No.
DTC Detecting Condition
Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
B1648/82
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the circuit for the front passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) for 2 seconds.
  1. Side airbag sensor RH malfunction
  2. Rear airbag sensor RH malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor RH
  3. Rear airbag sensor RH
  4. Center airbag sensor assembly

WIRING DIAGRAM


C165789E19


INSPECTION PROCEDURE

1.CHECK PRESENT DTC


    C157628E01
  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check the present DTCs (Click here).

    Result:
    Result
    Proceed to
    Present DTC B1628 or B1648 is output.
    A
    Present DTC B1647 or 82 is output.
    B
    Present DTC B1637 or B1638 is output.
    C
    Present DTC B1627 is output.
    D
    Present DTC B1627, B1628, B1637, B1638, B1647, B1648, or 82 is not output.
    E

    HINT:
    1. DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then on (IG) again.
    2. Codes other than present DTC B1627, B1628, B1637, B1638, B1647, B1648, and 82 may be output at this time, but they are not related to this check.



B
Go to step 3

C
Go to step 14

D
Go to step 21

E
USE SIMULATION METHOD TO CHECK (Click here)
A


2.CHECK PAST DTC
  1. Check the past DTCs (Click here).

    Result:
    Result
    Proceed to
    Past DTC B1627 or B1637 is not output.
    A
    Past DTC B1637 is output.
    B
    Past DTC B1627 is output.
    C

    HINT:
    Codes other than past DTC B1627 and B1637 may be output at this time, but they are not related to this check.



B
Go to step 14

C
Go to step 21
A


3.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, rear airbag sensor RH and the side airbag sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, rear airbag sensor RH and side airbag sensor RH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (OPEN)


    C168898E04
  1. Using SST, connect terminals 17 (BBP+) and 18 (BBP-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - N3-3 (BBR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT)


    C145456E04
  1. Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - N3-3 (BBR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT TO B+)


    C145456E04
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-3 (BBR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


7.CHECK FLOOR WIRE (SHORT TO GROUND)


    C145456E04
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-4 (BBR+) - Body ground
    Always
    1 MΩ or higher
    N3-3 (BBR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


8.CHECK FLOOR WIRE (OPEN)


    C145449E12
  1. Using SST, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-2 (BCR-) - N3-1 (BCR+)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


9.CHECK FLOOR WIRE (SHORT)


    C145445E08
  1. Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


10.CHECK FLOOR WIRE (SHORT TO B+)


    C145445E08
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


11.CHECK FLOOR WIRE (SHORT TO GROUND)


    C145445E08
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N3-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


12.CHECK SIDE AIRBAG SENSOR RH


    C167956E01
  1. Connect the connectors to the rear airbag sensor RH and the center airbag sensor assembly.

  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1628, B1647, B1648, or 82 is output.
    A
    DTC B1623, B1642, B1643, or 81 is output.
    B
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


13.CHECK REAR AIRBAG SENSOR RH


    C167953E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 are not output.
    A
    DTC B1628, B1647, B1648, or 82 is output.
    B
    DTC B1623, B1642, B1643, or 81 is output.
    C

    HINT:
    Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIR BAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

14.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the side airbag sensor RH and the rear airbag sensor RH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


15.CHECK FLOOR WIRE (OPEN)


    C145449E12
  1. Using SST, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


16.CHECK FLOOR WIRE (SHORT)


    C145445E08
  1. Disconnect SST from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - N3-2 (BCR-)
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


17.CHECK FLOOR WIRE (SHORT TO B+)


    C145445E08
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N3-2 (BCR-) - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
REPLACE FLOOR WIRE
OK


18.CHECK FLOOR WIRE (SHORT TO GROUND)


    C145445E08
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N3-1 (BCR+) - Body ground
    Always
    1 MΩ or higher
    N3-2 (BCR-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


19.CHECK SIDE AIRBAG SENSOR RH


    C166177E01
  1. Connect the connector to the rear airbag sensor RH.

  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1637 or B1638 is output.
    A
    DTC B1632 or B1633 is output.
    B
    DTC B1632 or B1633 and B1637 or B1638 are not output.
    C

    HINT:
    Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.



B
REPLACE SIDE AIRBAG SENSOR RH (Click here)

C
USE SIMULATION METHOD TO CHECK (Click here)
A


20.CHECK REAR AIRBAG SENSOR RH


    C166174E02
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.

  1. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1632 or B1633 and B1637 or B1638 are not output.
    A
    DTC B1637 or B1638 is output.
    B
    DTC B1632 or B1633 is output.
    C

    HINT:
    Codes other than DTC B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE REAR AIR BAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

21.CHECK SIDE AIRBAG SENSOR RH


    C166177E01
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Interchange the side airbag sensor LH with RH and connect the connectors to them.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B1622 and B1627 are not output.
    A
    DTC B1627 is output.
    B
    DTC B1622 is output.
    C

    HINT:
    Codes other than DTC B1622 and B1627 may be output at this time, but they are not related to this check.



B
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE SIDE AIRBAG SENSOR RH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)