Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the park/neutral position switch (for automatic transaxle) or clutch pedal switch (for manual transaxle) and also flows to terminal STA of the ECM (STA Signal).

WIRING DIAGRAM


A173974E01


INSPECTION PROCEDURE

HINT:
This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table (Click here).

1.INSPECT TERMINAL VOLTAGE (ST RELAY TERMINAL)


    A172711E01
  1. Remove the ST relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 1 - Body ground
    Engine cranking
    9 to 14 V

    HINT:
    The engine does not crank because the relay is not installed.

  1. Reinstall the ST relay.



NG
Go to step 11
OK


2.INSPECT ST RELAY


    B016200E02
  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When no battery voltage applied terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When the battery voltage applied terminals 1 and 2
    Below 1 Ω

  1. Reinstall the ST relay.



NG
REPLACE ST RELAY
OK


3.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)


    A172711E01
  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 2 - Body ground
    Always
    Below 1 Ω

  1. Reinstall the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - BODY GROUND)
OK


4.INSPECT TERMINAL VOLTAGE (ST RELAY TERMINAL)


    A172711E01
  1. Remove the ST relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 5 - Body ground
    Cranking
    9 to 14 V

  1. Reinstall the ST relay.



NG
Go to step 6
OK


5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER)


    A172722E01
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the starter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 - B12-1
    Always
    Below 1 Ω

  1. Reconnect the starter connector.

  1. Reinstall the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - STARTER)
OK

REPAIR OR REPLACE STARTER ASSEMBLY 

6.CHECK HARNESS AND CONNECTOR (ST RELAY - IGNITION SWITCH ASSEMBLY)


    A172723E02
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the ignition switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 5 - D24-7 (ST2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 5 or D24-7 (ST2) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the ignition switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - IGNITION SWITCH ASSEMBLY)
OK


7.INSPECT IGNITION SWITCH ASSEMBLY


    A158012E13
  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All terminals
    LOCK
    10 kΩ or higher
    D24-4 (AM1) - D24-3 (ST1)
    START
    Below 1 Ω

  1. Reconnect the ignition switch assembly connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH)


    A172724E01
  1. Remove the ST relay from the engine room relay block.

  1. Disconnect the park/neutral position switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 2 - B5-5
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 2 or B5-5 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the ST relay.

  1. Reconnect the park/neutral position switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH)
OK


9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (U151E: Click here, U151F: Click here).
    Result: 
    Result
    Proceed To
    OK
    A
    NG (with U151E)
    B
    NG (with U151F)
    C



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH (Click here)
A


10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH ASSEMBLY)


    A159666E04
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B5-4 - D24-3 (ST1)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B5-4 or D24-3 (ST1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - IGNITION SWITCH ASSEMBLY)
OK


11.INSPECT IGNITION SWITCH ASSEMBLY


    A158012E13
  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Ignition Switch Position
    Specified Condition
    All terminals
    LOCK
    10 kΩ or higher
    D24-4 (AM1) - D24-3 (ST1)
    START
    Below 1 Ω

  1. Reconnect the ignition switch assembly connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


12.INSPECT FUSE (AM1 FUSE)


    A168236E02
  1. Remove the AM1 fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    AM1 fuse
    Always
    Below 1 Ω

  1. Reinstall the AM1 fuse.



NG
REPLACE FUSE (AM1 FUSE)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)