DTC P050B Cold Start Ignition Timing Performance |
| DTC No. | DTC Detection Condition | Trouble Area |
| P050B | Ignition timing retard value insufficient for 5 seconds or more for 10 seconds of P050A monitoring duration at cold start (2 trip detection logic) |
|

| Related DTCs | P050B: Idle ignition timing problem at cold |
| Required Sensors / Components (Main) | Mass air flow meter |
| Required Sensors / Components (Related) | Engine Coolant Temperature (ECT) sensor, Throttle position sensor, Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0010, P0020 (OCV bank 1, 2) P0011, P0021 (VVT system bank 1, 2 - advance) P0012, P0022 (VVT system bank 1, 2 - retard) P0013, P0023 (Exhaust OCV bank 1, 2) P0014, P0024 (Exhaust VVT system bank 1, 2 - advance) P0016, P0018 (VVT system bank 1, 2 - misalignment) P0017, P0019 (Exhaust VVT system bank 1, 2 - misalignment) P0100, P0102, P0103 (MAF meter) P0115, P0117, P0118 (ECT sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (TP sensor) P0125 (Insufficient ECT for closed loop) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (CKP sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351, P0352, P0353, P0354, P0355, P0356 (Igniter) P0500 (Vehicle speed sensor) P2195, P2196, P2197, P2198 (A/F sensor - rationality) P2238, P2241, P2252, P2255 (A/F sensor - low impedance) P2239, P2242, P2253, P2256 (A/F sensor - high impedance) P2A00, P2A03 (A/F sensor - slow response) |
| Battery voltage | 8 V or more |
| Time after engine start | 3 seconds or more |
| Starter | OFF |
| ECT at engine start | -10°C (14°F) or more |
| ECT | -10 to 50°C (14 to 122°F) |
| Engine idling time | 3 seconds or more |
| Fuel-cut | OFF |
| Vehicle speed | Less than 1.875 mph (3 km/h) |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Accumulated time when ignition timing retard is cut off | 5 seconds or more |
| Symptoms | Factor | Trouble Area |
| Low idle speed at engine cold. | Excessive engine friction |
|
| Rough idle at engine cold. | Abnormal combustion | Fuel quality |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following the menu items: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P050B | A |
| P050B and other DTCs | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (FUEL TRIM) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.
Read the values displayed on the tester at engine idles.
Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total Fuel Trim.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 4.CHECK PCV HOSE CONNECTIONS |
|
| ||||
| OK | |
| 5.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage (Click here).
|
| ||||
| OK | |
| 6.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.
|
| ||||
| OK | |
| 7.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
|
| ||||
| 8.CHECK AND REPAIR VVT SENSOR |
|
| ||||
| 9.REPAIR OR REPLACE PCV HOSE |
|
| ||||
| 10.REPAIR OR REPLACE INTAKE SYSTEM |
|
| ||||
| 11.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
|
| ||||
| 12.CHECK THROTTLE VALVE |
Check for deposits around the throttle valve and throttle valve condition.
|
| ||||
| OK | |
| 13.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 14.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY |
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B) |
Connect the Techstream to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Switch the ECM from normal mode to check mode using the tester (Click here).
Start the engine to idle for a minute.
Read the DTCs.
| NEXT | ||
| ||