Home › SECURITIES › ENGINE IMMOBILISER › ID CODE BOX (w/ Smart Key System)

ID CODE BOX (w/ Smart Key System) > INSTALLATION

for Preparation Click here



1. INSTALL ID CODE BOX (IMMOBILISER CODE ECU)


    B170918
  1. Engage the 3 claws and install the ID code box (immobiliser code ECU) as shown in the illustration.



2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/o PTC Heater)
  1. Driver Side:

    1. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Passenger Side:

    1. Using a 12 mm hexagon wrench, adjust the position of the 2 collars.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }



  1. Connect the connector.


    E151011E01

  1. Install the 2 bolts and 2 caps to the engine compartment side.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



  1. Engage the cooler drain hose.


    E151007

  1. Connect the blower motor connector.

  1. Install the 2 nuts and bolt.

  1. Connect each connector.

  1. Connect the 2 earth wires with the 2 bolts <A>.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



  1. Engage each clamp.


    E151006E01



3. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/ PTC Heater)
  1. Driver Side:

    1. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Passenger Side:

    1. Using a 12 mm hexagon wrench, adjust the position of the 2 collars.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }



  1. Connect the connector.


    E151011E01

  1. Install the 2 bolts and 2 caps to the engine compartment side.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



  1. Engage the cooler drain hose.


    E151007

  1. Connect the 2 quick heater connectors.

  1. Connect the blower motor connector.

  1. Install the 2 nuts and bolt.

  1. Connect each connector.

  1. Connect the 2 earth wires with the 2 bolts <A>.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



  1. Engage each clamp.


    E151005E01



4. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E151002
  1. Install the 3 nuts.

  1. Install the 2 bolts.

  1. Install the No. 1 instrument panel brace sub-assembly with the screw.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    E151001
  1. Engage each clamp.

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E151004
  1. Install the 3 nuts.

  1. Install the bolt.

  1. Install the No. 2 instrument panel brace sub-assembly with the screw.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



    E151003
  1. Engage each clamp.

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



6. INSTALL CENTER HEATER TO REGISTER DUCT


    E150999
  1. Engage the 4 claws and install the center heater to register duct.

  1. Engage the clamp.



7. INSTALL NO. 1 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    E151000
  1. Install the clip and the No. 1 console box duct.



8. INSTALL REAR NO. 3 AIR DUCT


    E150998
  1. Engage the 2 claws and install the rear No. 3 air duct.

  1. Install the clip.



    E151083E01
  1. Engage the claw and install the floor carpet.



9. INSTALL REAR NO. 1 AIR DUCT


    E150997
  1. Engage the 2 claws and install the rear No. 1 air duct.

  1. Install the clip.

  1. Engage the clamp.



    E151082E01
  1. Engage the claw and install the floor carpet.



10. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY


    E150334
  1. Install the air conditioning amplifier assembly with the 2 screws.

  1. Connect each connector.



11. INSTALL CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    B170919
  1. Install the certification ECU (smart key ECU assembly) with the 2 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connectors.



12. INSTALL POWER STEERING ECU ASSEMBLY


    C166319
  1. Install the power steering ECU assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



    C167533E01
  1. Check that the connector lever is at the fully unlocked position before installation.

    NOTICE:
    If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.



    C165548E01
  1. Connect the 4 connectors to the power steering ECU assembly.

  1. Lightly pull on the connector and check that the connector does not disconnect.



13. CONNECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    E151587
  1. Connect the instrument panel junction block assembly with the 3 nuts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }



14. INSTALL STEERING COLUMN ASSEMBLY


    C166135E01
  1. Check that the 2 bushings are securely installed to the steering column assembly.

    HINT:
    If the bushings are missing or damaged, replace the steering column assembly with a new one.



    C166130
  1. Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.



    C166140
  1. Connect the connector to the power steering ECU assembly.



    C166139
  1. Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.



15. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


    C165545E01
  1. Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.



    C165544
  1. Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



    C166146
  1. Install the steering intermediate shaft sub-assembly to the steering column hole shield.



    C166145
  1. Tighten the bolt.



16. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY


    C166133
  1. Engage the 2 claws to install the No. 1 air duct sub-assembly.



17. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165102
  1. Install the DLC3 to the driver side knee airbag assembly with the 2 claws.



    C168041
  1. Connect the driver side knee airbag connector and tire pressure warning reset switch connector to the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



    C165100
  1. Support the driver side knee airbag assembly with one hand as shown in the illustration.



    C165099
  1. Temporarily install the driver side knee airbag assembly with the 2 hooks.



    C165098
  1. Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



18. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY


    C165374
  1. Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }



    C165373
  1. Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C165371
  1. Connect the brake pedal load sensing switch connector and engage the clamp.



19. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS


    C170591E01
  1. Apply lithium soap base glycol grease to the push rod pin.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.



20. INSTALL BRAKE PEDAL RETURN SPRING


    C165369
  1. Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.



21. INSTALL STOP LIGHT SWITCH ASSEMBLY


    E150075E01
  1. Temporarily install the stop light switch assembly with the stop light switch lock nut.



    E150611E01
  1. Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).

  1. Tighten the stop light switch lock nut.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }



    E150073
  1. Connect the connector.



22. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.



      C165370E01
    1. Turn back the carpet.

    2. Measure the shortest distance between the brake pedal surface and tibia pad.

      Pedal height from tibia pad:
      148.8 to 158.8 mm (5.858 to 6.252 in.)

  1. Adjust the brake pedal height.

    1. Disconnect the stop light switch connector.

    2. Remove the stop light switch assembly.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the brake pedal height by turning the push rod.

    5. Tighten the push rod clevis lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. Install and adjust the stop light switch .

      NOTICE:
      Do not depress the brake pedal.

    7. Connect the stop light switch connector.



23. INSPECT BRAKE PEDAL FREE PLAY


    C132708E01
  1. Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.

  1. Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance . If the pedal free play is as specified, proceed to the "INSPECT BRAKE PEDAL RESERVE DISTANCE" procedure.



24. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.



    C111339E05
  1. Release the parking brake lever.

  1. With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.

    Pedal reserve distance from the tibia pad at 500 N (51 kgf, 112 lbf):
    84.4 mm (3.32 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).



25. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Pole Antenna Type)
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <D> and nut <H>.



  1. Install the 2 clips.


    B168377E01

  1. Engage each clamp.

  1. Install the 2 passenger airbag bolts <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the bolt <E>.



  1. Connect each connector and install the instrument panel safety pad assembly.


    B206571E01



26. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Glass Antenna Type)
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <D> and nut <H>.



  1. Install the 2 clips.


    B168377E01

  1. Engage each clamp.

  1. Install the 2 passenger airbag bolts <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



  1. Connect each connector and install the instrument panel safety pad assembly.


    B168376E01



27. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165103
  1. Connect the connector.



28. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
  1. Connect the connector.



    E150560
  1. Install the front No. 2 speaker assembly with the 2 bolts.



29. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B173014
  1. Engage the 2 guides.

  1. Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.



30. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
  1. Connect the connector.



    E150560
  1. Install the front No. 2 speaker assembly with the 2 bolts.



31. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B168375
  1. Engage the 2 guides.

  1. Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.



32. INSTALL FRONT PILLAR GARNISH RH


    B173685E01
  1. Remove the protective cover.



    B173683E01
  1. Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.



33. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B173239E01
  1. Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



34. INSTALL FRONT PILLAR GARNISH LH


    B173226E01
  1. Remove the protective cover.



    B173223E01
  1. Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.



35. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B173235E01
  1. Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



36. INSTALL ENGINE SWITCH


    A170658
  1. Engage the 2 claws to install the switch.

  1. Connect the switch connector.



37. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B168374
  1. Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.



38. INSTALL FRONT NO. 1 CONSOLE BOX INSERT


    B168373
  1. Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.



39. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    B173629
  1. Engage the 6 claws.



    B173628
  1. Install the console box assembly with the 4 bolts and 2 screws.



40. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    B175149
  1. Engage the 6 claws.

  1. Connect the connector.



    B181135
  1. Install the console box assembly with the 4 bolts and 2 screws.



41. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.



42. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    B173013
  1. Install the No. 2 console box duct as shown in the illustration.



43. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    B168372
  1. Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.



44. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.



    B168370
  1. Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.



45. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    B173000
  1. Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.



46. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



47. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



48. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    B168371
  1. Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



49. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    B173009
  1. Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.



    B173021
  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.



50. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B173227
  1. Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.



51. INSTALL FRONT DOOR SCUFF PLATE LH


    B173224
  1. Engage the guide and the 8 claws, and install the front door scuff plate LH.



52. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
  1. Connect each connector.



    E150552
  1. Engage the 4 clips.



    E150551
  1. Install the radio receiver assembly with bracket with the 4 bolts.



53. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. Connect each connector.



    E150545
  1. Engage the 4 clips.



    E150544
  1. Install the navigation receiver assembly with bracket with the 4 bolts.



54. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector.



    E150368
  1. Engage the 4 clips and install the heater control and accessory assembly.



55. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
  1. Connect the connector.



    E150367
  1. Engage the 4 clips and install the air conditioning control assembly.



56. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B184681E01
  1. Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.



57. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    B168369
  1. Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.



58. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the connector.



    E152487
  1. Install the combination meter assembly with the 4 screws.



59. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    E152488
  1. Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.



60. POSITION FRONT WHEELS STRAIGHT AHEAD


61. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    C166129
  1. Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.



62. INSTALL STEERING COLUMN COVER


    C165716
  1. Engage the claw to install the upper steering column cover.



    C166128
  1. Engage the 2 claws to install the lower steering column cover.



    C165715
  1. Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }



63. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165096
  1. Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.



    C165097E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



64. INSTALL STEERING WHEEL ASSEMBLY


    C165708E01
  1. Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.



65. INSPECT STEERING WHEEL CENTER POINT


66. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.



    C165092
  1. Support the steering pad with one hand as shown in the illustration.



    C165093
  1. Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.



    C166982E01
  1. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



67. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    C165091
  1. Install the lower No. 2 steering wheel cover with the claw.



68. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    C165090
  1. Install the lower No. 3 steering wheel cover with the claw.



69. INSTALL FRONT WHEEL LH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



70. CONNECT COOLER REFRIGERANT LIQUID PIPE A
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant liquid pipe A.

  1. Install the cooler refrigerant liquid pipe A.



71. CONNECT NO. 1 COOLER REFRIGERANT SUCTION PIPE
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant suction pipe.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the No. 1 cooler refrigerant suction pipe.



    E150370
  1. Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



72. CONNECT HEATER INLET WATER HOSE


    E150372
  1. Install the heater inlet water hose and attach the clip.



73. CONNECT HEATER OUTLET WATER HOSE


    E150371
  1. Install the heater outlet water hose and attach the clip.



74. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY


    C165926E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



    C165925
  1. Engage the 4 clamps.



75. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    E150150
  1. Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.



76. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


  1. Engage the 20 claws.


    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.



    E150146
  1. Engage the 2 claws and connect the front fender to cowl side seal LH.



    E150147
  1. Engage the 2 claws and connect the front fender to cowl side seal RH.



77. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E147125E01
  1. Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)



78. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.



  1. When reinstalling:



      E112237E01
    1. Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.



    E152618E01
  1. Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



79. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



80. INSPECT STEERING PAD


    C166979
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



81. INSPECT SRS WARNING LIGHT
(Click here)


82. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.



    A169415E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    w/o Trailer Towing System 
    Condition
    Specified Condition
    w/ Rear Heater
    11.0 liters (11.6 US qts, 9.7 Imp. qts)
    w/o Rear Heater
    8.8 liters (9.3 US qts, 7.7 Imp. qts)
    w/ Trailer Towing System 
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



83. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A169405
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



84. CHARGE WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.



  1. Charge with refrigerant HFC-134a (R134a).


    E143108E02

    Standard (w/o Rear Air Conditioning System):
    550 to 650 g (19.4 to 22.9 oz.)

    Standard (w/ Rear Air Conditioning System):
    720 to 820 g (25.4 to 28.9 oz.)

    SST
    09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02140, 09985-02080)

    NOTICE:
    1. Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, not with the sight glass.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an A/C system.



85. WARM UP ENGINE
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.



86. INSPECT FOR REFRIGERANT LEAK
  1. After recharging with refrigerant gas, inspect for refrigerant leak using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Make sure that the ignition switch is off.
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)



    I042222E25
  1. Using a gas leak detector, inspect for refrigerant leak from the refrigerant lines.



    N014519E06
  1. Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.

  1. If a gas leak is not detected from the drain hose, remove the blower motor from the cooling unit. Insert the gas leak detector into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.



87. REGISTER ECU COMMUNICATION ID

NOTICE:
When replacing the ID code box (immobiliser code ECU), perform initialization (Click here).



88. REGISTER KEY

NOTICE:
When replacing the ID code box (immobiliser code ECU), perform initialization (Click here).