Home › TRANSMISSION ยท U151E AUTOMATIC TRANSAXLE › DIFFERENTIAL OIL SEAL

DIFFERENTIAL OIL SEAL > REPLACEMENT

for Preparation Click here



1. REMOVE ENGINE UNDER COVER ASSEMBLY


    A171849
  1. Remove the 2 bolts and engine under cover assembly RR.



    A171850
  1. Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.



2. REMOVE NO. 1 ENGINE UNDER COVER


    A171855
  1. Remove the 6 bolts, 2 clips and No. 1 engine under cover.



3. REMOVE NO. 2 ENGINE UNDER COVER


    A171854
  1. Remove the 2 bolts and No. 2 engine under cover.



4. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



5. REMOVE FRONT WHEEL


6. REMOVE FRONT AXLE HUB NUT LH


    C167528E01
  1. Using SST and a hammer, release the staked part of the front axle hub nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.



7. REMOVE FRONT AXLE HUB NUT RH

HINT:
Perform the same procedure for the LH side.



8. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH


    C165915
  1. Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



9. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



10. SEPARATE FRONT SPEED SENSOR LH


    C165818E03
  1. Remove the bolt and resin clamp, and separate the front speed sensor.



11. SEPARATE FRONT SPEED SENSOR RH

HINT:
Perform the same procedure for the LH side.



12. SEPARATE TIE ROD ASSEMBLY LH
  1. Remove the cotter pin and the nut.



    C165542E01
  1. Install SST to the tie rod end.

    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.



  1. Using SST, separate the tie rod end from the steering knuckle.


    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.



13. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



14. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM LH


    C165929
  1. Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.



15. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT:
Perform the same procedure for the LH side.



16. SEPARATE FRONT AXLE ASSEMBLY LH


    C165537E05
  1. Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.



    C165534
  1. Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.



17. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



18. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    C165535E01
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the drive shaft dust cover, boot, or oil seal.
    2. Be careful not to drop the drive shaft assembly.



19. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)


    C167529
  1. Remove the bearing bracket hole snap ring from the drive shaft bearing bracket.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

    NOTICE:
    Do not damage the boot or oil seal.



20. SECURE FRONT AXLE HUB SUB-ASSEMBLY LH


    F045045E03
  1. Using SST, secure the front axle hub bearing.

    SST
    09608-16042   (09608-02021, 09608-02041)

    NOTICE:
    The hub bearing may be damaged if it is subjected to the vehicle's full weight, such as when moving the vehicle with the drive shaft removed. If it is necessary to place the vehicle's weight on the hub bearing, first support it with SST.



21. SECURE FRONT AXLE HUB SUB-ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



22. REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL


    C083058E02
  1. Using SST, pull out the oil seal.

    SST
    09308-00010  



23. REMOVE TRANSAXLE HOUSING OIL SEAL


    C083057
  1. Using SST, pull out the oil seal.

    SST
    09308-00010  



24. INSTALL TRANSAXLE HOUSING OIL SEAL


    C083054E04
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, install a new oil seal.

    SST
    09316-60011   (09316-00011)

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)



25. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL


    C083053E01
  1. Coat the lip of a new oil seal with MP grease.

  1. Using SST and a hammer, install a new oil seal.

    SST
    09223-15020  
    09950-70010   (09951-07150)

    Oil seal installation depth:
    -0.5 to 0.2 mm (-0.020 to 0.008 in.)



26. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    C165536
  1. Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.

    NOTICE:
    1. Set the shaft snap ring with the opening facing down.
    2. Be careful not to damage the drive shaft dust cover, boot, or oil seal.
    3. Move the drive shaft assembly while keeping it level.



27. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)
  1. Install the front drive shaft assembly RH.



    C167529
  1. Install a new bearing bracket hole snap ring and bolt.

    Torque:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    1. Do not damage the boot or oil seal.
    2. Move the drive shaft assembly while keeping it level.



28. INSTALL FRONT AXLE ASSEMBLY LH


    C165537E05
  1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.



29. INSTALL FRONT AXLE ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



30. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM LH


    C167143
  1. Remove the 3 bolts, nut, and the front lower suspension arm from the front frame assembly.

  1. Remove the front lower arm bushing stopper from the front lower suspension arm.



31. INSTALL NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT:
Perform the same procedure for the LH side.



32. INSTALL TIE ROD ASSEMBLY LH
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



33. INSTALL TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



34. INSTALL FRONT SPEED SENSOR LH


    C165818E03
  1. Install the resin clamp and front speed sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Prevent foreign matter from attaching to the sensor tip.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.



35. INSTALL FRONT SPEED SENSOR RH

HINT:
Perform the same procedure for the LH side.



36. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


    C165915
  1. Install the front stabilizer link assembly to the front shock absorber with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.



37. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure for the LH side.



38. INSTALL FRONT AXLE HUB NUT LH
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    HINT:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.



    C165538
  1. Using a socket wrench (30 mm), install a new axle hub nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the front axle hub nut.



39. INSTALL FRONT AXLE HUB NUT RH

HINT:
Perform the same procedure for the LH side.



40. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



41. ADD AUTOMATIC TRANSAXLE FLUID


42. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. Park the vehicle on a level surface and set the parking brake.



    D025120E05
  1. With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to S1 and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put the dipstick back all the way.

  1. Take out the dipstick again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
    If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
    If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.



43. INSTALL NO. 2 ENGINE UNDER COVER


    A171854
  1. Install the No. 2 engine under cover with the 2 bolts.



44. INSTALL NO. 1 ENGINE UNDER COVER


    A171855
  1. Install the No. 1 engine under cover with the 6 bolts and 2 clips.



45. INSTALL ENGINE UNDER COVER ASSEMBLY


    A171850
  1. Install the engine under cover assembly with the 4 bolts and 5 clips.



    A171849
  1. Install the engine under cover assembly RR with the 2 bolts.



46. INSTALL FRONT WHEEL ALIGNMENT

HINT:
(Click here)



47. INSTALL ABS SPEED SENSOR SIGNAL

HINT:
(Click here)