Home › HYBRID SYSTEM ยท P310 › HYBRID BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A7F-123    Hybrid Battery Pack Deterioration

for Preparation Click here


DESCRIPTION


  1. The battery smart unit and the hybrid vehicle control ECU calculate the SOC (state of charge) of the HV battery through the accumulated amperage in the HV battery. The battery smart unit sends the condition of the HV battery to the hybrid vehicle control ECU. Then the hybrid vehicle control ECU calculates the SOC based on the information and controls HV battery charge and discharge according to the driving condition.


    A171602E02


    DTC No.
    DTC Detection Condition
    Trouble Area
    P0A7F-123
    1. Internal resistance of the HV battery is higher than the standard (1 trip detection)
    2. Difference in the capacity between battery blocks is larger than the standard (2 trip detection)
    1. HV battery assembly
    2. Battery smart unit

    HINT:
    P0A7F-123 will not be set unless the vehicle is driven for approximately 10 minutes after clearing the DTC.


MONITOR DESCRIPTION

The battery smart unit calculates the resistance of the HV battery through amperage and voltage, and uses this resistance to determine the extent of deterioration of the HV battery. If the battery smart unit detects that the resistance of the HV battery has exceeded the standard, it determines that a malfunction has occurred. In addition, the battery smart unit monitors the SOC, and if the difference between the maximum and minimum SOC values exceeds the standard, it determines that a malfunction has occurred. When either of the malfunction detection conditions is met, the hybrid vehicle control ECU illuminates the MIL and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0A7F-123: Rationality
Required sensors/components
Main: Battery voltage sensor inside battery smart unit, battery current sensor
Sub: Battery temperature sensor
Frequency of operation
Continuous
Duration
TOYOTA's intellectual property
MIL operation
Immediately or 2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever the DTCs listed are not present
TOYOTA's intellectual property

TYPICAL MALFUNCTION THRESHOLDS


TOYOTA's intellectual property
-

COMPONENT OPERATING RANGE


Battery smart unit
DTC P0A7F-123 is not detected

INSPECTION PROCEDURE

1.CHECK DTC OUTPUT (DTC P0A1F-123 IS OUTPUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0A1F-123 is not output.
    A
    P0A1F-123 is also output.
    B



B
GO TO DTC CHART (P0A1F-123) (Click here)
A


2.INSPECT BATTERY SMART UNIT
  1. Ensure the safety of the areas in front and at the back of the vehicle.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (READY).

  1. Select the following menu items: Powertrain / Hybrid Control / Data List / V1 to 15 Batt block.

  1. Fully warm up the engine and turn the air conditioning off.

  1. Firmly depress the brake pedal with your left foot.

  1. Move the shift lever to the D position.

  1. Record each battery block voltage from the data list (V1 to 15 Batt block) while fully depressing the accelerator pedal.

  1. Compare the battery block voltages (V1 to 15 Batt block) between the even and odd number groups in each combination shown in the table below.

    Odd number group
    Even number group
    Battery block voltages to be compared
    V1 BATT BLOCK
    V2 BATT BLOCK
    V1 BATT BLOCK - V2 BATT BLOCK
    V3 BATT BLOCK
    V4 BATT BLOCK
    V3 BATT BLOCK - V4 BATT BLOCK
    V5 BATT BLOCK
    V6 BATT BLOCK
    V5 BATT BLOCK - V6 BATT BLOCK
    V7 BATT BLOCK
    V8 BATT BLOCK
    V7 BATT BLOCK - V8 BATT BLOCK
    V9 BATT BLOCK
    V10 BATT BLOCK
    V9 BATT BLOCK - V10 BATT BLOCK
    V11 BATT BLOCK
    V12 BATT BLOCK
    V11 BATT BLOCK - V12 BATT BLOCK
    V13 BATT BLOCK
    V14 BATT BLOCK
    V13 BATT BLOCK - V14 BATT BLOCK
    V15 BATT BLOCK
    V12 BATT BLOCK
    V15 BATT BLOCK - V12 BATT BLOCK

  1. Check that the difference in voltage of each combination is 0.3 V or more.

    Result:
    Result
    Proceed to
    Difference in voltage of each combination is less than 0.3 V.
    A
    Difference in voltage of each combination is 0.3 V or more.
    B

    HINT:
    Difference in voltage of each combination is 0.3 V or more due to a battery smart unit internal error.



B
REPLACE BATTERY SMART UNIT (Click here)
A

REPLACE HV BATTERY ASSEMBLY (Click here)