Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Put the engine in inspection mode (Click here).

  2. Warm up the engine.

  3. Turn the power switch off.

  4. Connect the Techstream to the DLC3.

  5. Turn the power switch on (IG).

  6. Turn the Techstream on.

  7. Enter the following menus: Powertrain / Engine and ECT / Data List.

  8. Check the values by referring to the table below.

    Tester Display
    Measurement Item/Range
    Normal Condition*1
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383.75 rpm
    850 to 950 rpm: Idling
    (Inspection mode)
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 22%: Idling
      (Inspection mode)
    1. 12.1 to 18.2%: Running without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from MAF meter/
    Min.: 0 gm/sec., Max.: 655.35 gm/sec.
    2.0 to 4.3 gm/s: Idling
    (Inspection mode)
    2.4 to 4.3 gm/s: 2500 rpm
    (without load)
    If value is approximately 0.0 g/s:
    1. Mass air flow meter power source circuit open
    1. VG circuit open or shorted
    If value is 271.0 g/s or more:
    1. E2G circuit open
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C, Max.: 140°C
    80 to 100°C
    (176 to 212°F): After warming up
    1. If value is -40°C (-40°F): sensor circuit open
    1. If value is 140°C (284°F): sensor circuit shorted
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    1. If value is -40°C (-40°F): sensor circuit open
    1. If value is 140°C (284°F): sensor circuit shorted
    Engine Run Time
    Engine run time/
    Min.: 0 s,
    Max.: 65.535 s
    Time after engine start
    Service data
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 120°C
    Coolant temperature when engine started
    Service data
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 120°C
    Intake air temperature when engine started
    Service data
    Battery Voltage
    Battery voltage/
    Min.: 0, Max.: 65.535 V
    9 to 14 V: Idling
    (Inspection mode)
    -
    Accel Sens. No. 1 Volt %
    Accelerator position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Accel Sens. No. 2 Volt %
    Accelerator position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Throttle Sensor Volt %
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 24%: Throttle fully closed
    1. 36 to 68%: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Sensor #2 Sensor Volt %
    Throttle sensor positioning #2/
    Min.: 0%, Max.: 100%
    -
    Calculated value based on VTA2
    System Guard
    System guard/ ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor is detecting idle/ ON or OFF
    Idling: ON
    (Inspection mode)
    Read value with intrusive operation (active test)
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 5 V
    0.5 to 1.0 V: Idling
    (Inspection mode)
    -
    Throttle Sensor Position
    Throttle sensor positioning/
    Min.: 0%, Max.: 100%
    0 to 10%: Idling
    (Inspection mode)
    Calculated value based on VTA
    Throttle Position No. 1
    Throttle position sensor No. 1 output voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Throttle Position No. 2
    Throttle position sensor No. 2 output voltage: Min.: 0 V, Max.: 4.98 V
    -
    ETCS freeze frame data
    Throttle Position No. 1
    Throttle position No. 1/
    Min.: 0 V, Max.: 5 V
    1. 0.5 to 1.2 V: Throttle fully closed
    1. 1.8 to 3.4 V: Throttle fully open
    -
    Throttle Position No.2
    Throttle position No. 2/
    Min.: 0 V, Max.: 5 V
    1. 2.1 to 3.1 V: Throttle fully closed
    1. 4.5 to 5.0 V: Throttle fully open
    Read value with intrusive operation (active test)
    Throttle Position command
    Throttle position command value/
    Min.: 0 V, Max.: 4.9804 V
    0.5 to 4.8 V
    ETCS service data
    Throttle Sens Open Pos #1
    Throttle sensor opener position No. 1/
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 1.0 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle sensor opener position No. 2/
    Min.: 0 V, Max.: 4.9804 V
    2.0 to 2.6 V
    ETCS service data
    Throttle Sens Open #1 (AD)
    Throttle sensor opener position No. 1 (AD)/
    Min.: 0 V, Max.: 4.9804 V
    0.6 to 0.9 V
    ETCS service data
    Throttle Motor
    Whether or not throttle motor control is permitted/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    Throttle Motor Current
    Throttle motor current/
    Min.: 0 A, Max.: 80 A
    0 to 3.0 A: Idling
    (Inspection mode)
    -
    Throttle Motor Duty
    Throttle motor/
    Min.: 0%, Max.: 100%
    0.5 to 40%: Idling
    (Inspection mode)
    -
    Throttle Motor Current
    Throttle actuator current: Min.: 0 A, Max.: 19.92 A
    0 to 3.0 A: Idling
    -
    Throttle Motor Open Duty
    Throttle actuator opening duty ratio: Min.: 0%, Max.: 100%
    0 to 40%: Idling
    When accelerator pedal depressed, duty ratio increased
    Throttle Motor Close Duty
    Throttle actuator closed duty ratio: Min.: 0%, Max.: 100%
    0 to 40%: Idling
    When accelerator pedal released quickly, duty ratio increased
    Throttle Motor Duty (Open)
    Throttle motor duty ratio (open)/
    Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle motor duty ratio (close)/
    Min.: 0%, Max.: 100%
    -
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed
    (learned value)/
    Min.: 0 V, Max.: 5 V
    0.4 to 0.8 V
    -
    ETCS Actuator Power
    Whether or not electric throttle control system power is input/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    +BM Voltage
    +BM voltage/
    Min.: 0, Max.: 19.92182
    10 to 15 V: Idling
    (Inspection mode)
    ETCS service data
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    Idling: ON
    (Inspection mode)
    -
    Clutch Current
    "Clutch Current: Min.: 0 A, Max.: 2.49 A"
    -
    -
    Fail Safe Drive
    Whether or not fail safe function is executed/ ON or OFF
    ETCS has failed: ON
    -
    Fail Safe Drive (Main CPU)
    Whether or not fail safe function is executed/ ON or OFF
    ETCS has failed: ON
    -
    Injector (Port)
    Injection period of No. 1 cylinder/
    Min.: 0 ms, Max.: 32.64 ms
    1.5 to 2.7 ms: Idling
    (Inspection mode)
    -
    Fuel Pump/Speed Status
    Fuel pump status/
    ON or OFF
    -
    Active Test support data
    Vacuum Pump
    Key-off EVAP system pump status/
    ON or OFF
    -
    Active Test support data
    EVAP (Purge) VSV
    EVAP (Parge) VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: Idling
    During idling: 1500 rpm
    Order signal from ECM
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 102.4%
    0 to 100%: Idling
    (Inspection mode)
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -50, Max.: 350
    -30 to 0 Idling
    (Inspection mode)
    Service data
    Vapor Pressure Pump
    EVAP vapor pressure/
    Min.: 33.853 kPa, Max.: 125.596 kPa
    Atmospheric pressure: Fuel tank cap removed
    -
    Vapor Pressure Tank
    Vapor pressure/
    Min.: -19.375 kPa, Max.: 24.375 kPa
    -
    Pressure inside fuel tank monitored by vapor pressure sensor
    EVAP Vapor Pressure (Wide)
    EVAP Vapor Pressure/
    Min.: -32.76 kPa, Max.: 32.76 kPa
    -
    -
    Vapor Pressure (Calculate)
    Vapor pressure (calculated)/
    Min.: -5.632 kPa, Max.: 715.264 kPa
    -
    -
    EVAP System Vent Valve
    Key-off EVAP system vent valve status/
    ON or OFF
    -
    Active Test support data
    Fuel Filler Opener
    Fuel filler cap status/
    ON or OFF
    -
    Active Test support data
    Fuel Vapor-Containment Valve
    Key-off EVAP system vapor-containment valve status/
    ON or OFF
    -
    Active Test support data
    Fuel Lid
    Fuel lid/
    Open or Close
    -
    -
    Fuel Lid Switch
    Fuel lid switch/
    ON or OFF
    -
    -
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    Active Test support data
    Target Air-Fuel Ratio
    Air-fuel ratio/
    Min.: 0, Max.: 1.999
    0.8 to 1.2: During idling
    (Inspection mode)
    -
    AF Lambda B2S1
    Short-term fuel trim associated with bank 2 sensor 1/
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = RICH
    1. Stoichiometric air-fuel ratio=1
    1. Value greater than 1 (1.001 to 1.999) = LEAN
    -
    AF FT B1S1
    Short-term fuel trim associated with bank 1 sensor 1/
    Min.: 0, Max.: 1.999
    1. Value less than 1 (0.000 to 0.999) = RICH
    1. Stoichiometric air-fuel ratio=1
    1. Value greater than 1 (1.001 to 1.999) = LEAN
    -
    AFS Voltage B1S1
    A/F sensor output voltage for bank 1 sensor 1/
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    (Inspection mode)
    Performing Control the Injection Volume or Control the Injection Volume A/F sensor function of Active Test enables technician to check output voltage of sensors
    AFS Voltage B2S1
    A/F sensor output voltage for bank 2 sensor 1/
    Min.: 0 V, Max.: 7.999 V
    2.8 to 3.8 V: Idling
    (Inspection mode)
    Performing Control the Injection Volume or Control the Injection Volume A/F sensor function of Active Test enables technician to check output voltage of sensors
    AFS Current B1S1
    "AFS B1 S1: Min.: -128 mA, Max.: 127.99 mA"
    -
    Performing Control the Injection Volume or Control the Injection Volume A/F sensor function of Active Test enables technician to check output current of sensors
    AFS Current B2S1
    "AFS B2 S1: Min.: -128 mA, Max.: 127.99 mA"
    -
    Performing Control the Injection Volume or Control the Injection Volume A/F sensor function of Active Test enables technician to check output current of sensors
    O2S B1 S2
    Heated oxygen sensor output voltage for bank 1 sensor 2/
    Min.: 0 V Max.: 1.275 V
    0.1 to 0.9 V:
    Driving at 47 mph (75 km/h)
    Performing Control the Injection Volume or Control the Injection Volume A/F sensor function of Active Test enables technician to check output voltage of sensor
    O2S B2 S2
    Heated oxygen sensor output voltage for bank 2 sensor 2/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving at 47 mph (75 km/h)
    Performing Control the Injection Volume or Control the Injection Volume A/F sensor function of Active Test enables technician to check output voltage of sensor
    O2S Impedance B1S2
    Sub O2S Impedance bank 1 sensor 2/
    Min.: 0 Ω, Max.: 21247.68 Ω
    5 to 15000 Ω
    -
    O2S Impedance B2S2
    Sub O2S Impedance bank 2 sensor 2/
    Min.: 0 Ω, Max.: 21247.68 Ω
    5 to 15000 Ω
    -
    Short FT #1
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #1
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Overall fuel compensation carried out long-term to compensate for continual deviation of short-term fuel trim from central value
    Total FT #1
    Total fuel trim of bank 1
    average value for fuel trim system of bank 1/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    (Inspection mode)
    -
    Short FT #2
    Short-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
    Long FT #2
    Long-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    0 +/- 20%
    Overall fuel compensation carried out long-term to compensate for continual deviation of short-term fuel trim from central value
    Total FT #2
    Total fuel trim of bank 1
    average value for fuel trim system of bank 2/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    (Inspection mode)
    -
    Fuel System Status #1
    Fuel system status (Bank 1)/
    OL or CL or OL DRIVE or OL FAULT or CL FAULT
    CL: Idling after warming up
    (Inspection mode)
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    1. OL FAULT: Open loop due to detected system fault
    1. CL FAULT: Closed loop but heated oxygen sensor, which is used for fuel control, malfunctioning
    Fuel System Status #2
    Fuel system status (Bank 2)/
    OL or CL or OL DRIVE or OL FAULT or CL FAULT
    CL: Idling after warming up
    (Inspection mode)
    1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
    1. CL (Closed Loop): Using heated oxygen sensor as feedback for fuel control
    1. OL DRIVE: Open loop due to driving conditions (fuel enrichment)
    1. OL FAULT: Open loop due to detected system fault
    1. CL FAULT: Closed loop but heated oxygen sensor, which is used for fuel control, malfunctioning
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 5 to 25°: Idling
    (Inspection mode)
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min: -64°CA, Max.: 1984°CA
    -24 to 0°CA:
    Driving at 47 mph (75 km/h)
    Service data
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min: -64°CA, Max.: 1,984°CA
    0 to 24°CA:
    Driving at 47 mph (75 km/h)
    Service data
    VVT Control Status #1
    VVT control (bank 1) status/
    ON or OFF
    -
    Active Test support data
    VVT Control Status #2
    VVT control (bank 2) status/
    ON or OFF
    -
    Active Test support data
    VVT Aim Angle #1
    VVT aim angle (bank 1)/
    Min.: 0%, Max.: 100%
    0%: Idling
    (Inspection mode)
    VVT duty signal value during intrusive operation
    VVT Change Angle #1
    VVT change angle/
    Min.: 0°FR, Max.: 60°FR
    0 to 5°FR: Idling
    (Inspection mode)
    Displacement angle during intrusive operation
    VVT OCV Duty #1
    VVT oil control valve operation duty/
    Min.: 0%, Max.: 100%
    0%: Idling
    (Inspection mode)
    Requested duty value for intrusive operation
    VVT Aim Angle #2
    VVT aim angle (bank 2)/
    Min.: 0%, Max.: 100%
    0%: Idling
    (Inspection mode)
    VVT duty signal value during intrusive operation
    VVT Change Angle #2
    VVT change angle (bank 2)/
    Min.: 0°FR, Max.: 60°FR
    0 to 5°FR: Idling
    (Inspection mode)
    Displacement angle during intrusive operation
    VVT OCV Duty #2
    VVT oil control valve (bank 2) operation duty/
    Min.: 0%, Max.: 100%
    0%: Idling
    (Inspection mode)
    Requested duty value for intrusive operation
    Catalyst Temp B1S1
    Catalyst temperature (Bank 1, sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S1
    Catalyst temperature (Bank 2, sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B1S2
    Catalyst temperature (Bank 1, sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S2
    Catalyst temperature (Bank 2, sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    -
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    1. OFF: Throttle open
    -
    Engine Oil Pressure SW
    Engine oil pressure switch/
    ON or OFF
    -
    -
    Check Mode
    Check mode/
    0: OFF, 1: ON
    ON: Check mode ON
    Click here
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    -
    -
    Misfire Test
    Check mode result for misfire monitor/
    0: Complete, 1: Incomplete
    -
    -
    OXS1 Test Result
    Check mode result for HO2 sensor (bank 1)/
    0: Complete, 1: Incomplete
    -
    -
    OXS2 Test Result
    Check mode result for HO2 sensor (bank 2)/
    0: Complete, 1: Incomplete
    -
    -
    A/F Test Results #2
    Check mode result for air-fuel ratio sensor (bank 2)/
    0: Complete, 1: Incomplete
    -
    -
    A/F Test Results #1
    Check mode result for air-fuel ratio sensor (bank 1)/
    0: Complete, 1: Incomplete
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    NOT AVL or AVAIL
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    NOT AVL or AVAIL
    -
    -
    Misfire Monitor
    Misfire monitor/ NOT AVL or AVAIL
    -
    -
    EGR/VVT Monitor
    EGR monitor/ NOT AVL or AVAIL
    -
    -
    EGR/VVT Monitor
    EGR monitor/ Complete or Incomplete
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    NOT AVL or AVAIL
    -
    -
    O2S (A/FS) Heater Monitor
    O2S (A/FS) heater monitor: Complete or Incomplete
    -
    -
    O2S (A/FS) Monitor
    O2S (A/FS ) heater monitor/
    NOT AVL or AVAIL
    -
    -
    O2S(A/FS) Monitor
    O2S(A/FS) monitor: complete or Incomplete
    -
    -
    A/C Monitor
    A/C monitor/
    NOT AVL or AVAIL
    -
    -
    A/C Monitor
    A/C monitor: complete or Incomplete
    -
    -
    2nd Air Monitor
    2nd air monitor/
    NOT AVL or AVAIL
    -
    -
    2nd Air Monitor
    2nd air monitor: complete or Incomplete
    -
    -
    EVAP Monitor
    EVAP monitor/
    NOT AVL or AVAIL
    -
    -
    EVAP Monitor
    EVAP monitor: complete or Incomplete
    -
    -
    Heated Catalyst Monitor
    Catalyst monitor/
    NOT AVL or AVAIL
    -
    -
    Heated Catalyst Monitor
    Catalyst monitor: complete or Incomplete
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    NOT AVL or AVAIL
    -
    -
    Catalyst Monitor
    Catalyst monitor: complete or Incomplete
    -
    -
    Component Monitor ENA
    Comprehensive component monitor/
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive component monitor/
    Complete or Incomplete
    -
    -
    Fuel System Monitor ENA
    Fuel system monitor/
    Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel system monitor/
    Complete or Incomplete
    -
    -
    Misfire Monitor ENA
    Misfire monitor/
    Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire monitor/
    Complete or Incomplete
    -
    -
    EGR/VVT Monitor ENA
    EGR monitor/
    Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR monitor/
    Complete or Incomplete
    -
    -
    Heater Monitor ENA
    O2S (A/F sensor) heater monitor/
    Unable or Enable
    -
    -
    Heater Monitor CMPL
    O2S (A/F sensor) heater monitor/
    Complete or Incomplete
    -
    -
    O2S (A/FS) Monitor ENA
    O2S (A/F sensor) monitor/
    Unable or Enable
    -
    -
    O2S (A/FS) Monitor CMPL
    O2S (A/F sensor) monitor/
    Complete or Incomplete
    -
    -
    A/C Monitor ENA
    A/C monitor/
    Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C monitor/
    Complete or Incomplete
    -
    -
    2nd Air Monitor ENA
    2nd air monitor/
    Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd air monitor/
    Complete or Incomplete
    -
    -
    EVAP Monitor ENA
    EVAP monitor/
    Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP monitor/
    Complete or Incomplete
    -
    -
    Heated Cat Monitor ENA
    Heated catalyst monitor/
    Unable or Enable
    -
    -
    Heated Cat Monitor CMPL
    Heated catalyst monitor/
    Complete or Incomplete
    -
    -
    Catalyst Monitor ENA
    Catalyst monitor/
    Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst monitor/
    Complete or Incomplete
    -
    -
    #Codes (Include History)
    #Codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km,
    Max.: 65535 km
    Distance after DTC detected
    -
    Running Time From MIL ON
    Running time from MIL ON/
    Min.: 0 min,
    Max.: 65535 min
    Equivalent to running time after MIL ON
    -
    Time after DTC Cleared
    Time after DTC cleared/
    Min.: 0 min,
    Max.: 65535 min
    Equivalent to time after DTCs erased
    -
    Distance from DTC Cleared
    Distance after DTC cleared/
    Min.: 0 km, Max.: 65535 km
    Equivalent to drive distance after DTCs erased
    -
    Warmup Cycle Cleared DTC
    Warm-up cycle after DTC cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTC cleared
    OBD Requirement
    OBD requirement
    OBD2
    -
    Number of Emission DTC
    Emission related DTCs
    -
    Number of emission related DTCs
    TC and TE1
    TC and TE1 terminals of DLC3/
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 800
    0 to 600
    -
    Cylinder #1 Misfire Count
    Misfire ratio of cylinder 1/
    Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #2 Misfire Count
    Misfire ratio of cylinder2/
    Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #3 Misfire Count
    Misfire ratio of cylinder 3/
    Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #4 Misfire Count
    Misfire ratio of cylinder 4/
    Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #5 Misfire Count
    Misfire ratio of cylinder 5/
    Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    Cylinder #6 Misfire Count
    Misfire ratio of cylinder 6/
    Min.: 0, Max.: 255
    0%
    This item displayed only during idling
    All Cylinder Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0 to 30
    -
    Misfire RPM
    Engine RPM for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -100%, Max.: 99.22%
    -100 to 99.22%
    Misfire detecting margin
    Electric Fan Motor
    Electric fan motor/
    ON or OFF
    -
    Active Test support data
    Idle Fuel Cut
    Idle fuel cut/
    ON or OFF
    -
    -
    FC TAU
    FC TAU/
    ON or OFF
    -
    -
    Model Code
    Model code
    -
    Identifying model code:
    MHU###
    Engine Type
    Engine type
    -
    Identifying engine type:
    3MZFE
    Cylinder Number
    Cylinder number/
    Min.: 0, Max.: 255
    -
    Identifying cylinder number:
    6
    Destination
    Destination
    -
    Identifying destination:
    A (America)
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Identifying model year:
    200#
    System Identification
    System identification
    -
    Identifying engine system:
    HV
    Requested Engine Torque
    Requested engine torque/
    Min.: 0 kW, Max.: 16383.75 kW
    0 to 57 kW
    Flag information for hybrid vehicle
    HV Target Engine Speed
    HV target engine speed/
    Min.: 0 rpm, Max.: 6375 rpm
    0 to 5000 rpm
    Flag information for hybrid vehicle
    Actual Engine Torque
    Actual engine torque/
    Min.: -128 Nm, Max.: 127 Nm
    -128 to 127 Nm
    Flag information for hybrid vehicle
    Estimated Engine Torque
    Estimated engine torque/
    Min.: 0 Nm, Max.: 510 Nm
    0 to 120 Nm
    Flag information for hybrid vehicle
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 255 s
    0 to 255 seconds
    Flag information for hybrid vehicle
    Request Engine Run Time
    Request engine run time/
    Min.: 0 s, Max.: 25.5 s
    0 to 25.5 seconds
    Flag information for hybrid vehicle
    Judge Time Engine Ignition
    Judgment time for ignition of engine/
    Min.: 0 s, Max.: 25.5 s
    0 to 25.5 seconds
    Flag information for hybrid vehicle
    Judge Time Engine Output
    Judgment time for engine output/
    Min.: 0 s, Max.: 25.5 s
    0 to 25.5 seconds
    Flag information for hybrid vehicle
    Fuel Level
    Fuel level/
    0: EMPTY, 1: NOT EMPTY
    -
    -
    ISC Learning
    ISC learning/
    0: Incomplete, 1: Complete
    -
    -
    F/C for Engine Stop Req
    Fuel cut for engine stop request/
    0: OFF, 1: ON
    -
    -
    Engine Independent
    Engine independently operation/
    0: NOT OPR, 1: OPERATE
    -
    -
    Racing Operation
    Racing operation/
    0: NOT OPR, 1: OPERATE
    -
    -
    Request Warm-up
    Request engine warm-up/
    0: NOT REQ, 1: REQUEST
    -
    -
    Engine Independent Control
    Engine independently control operation/
    0: NOT OPR, 1: OPERATE
    -
    -
    ISC Learning Value
    ISC learning value/
    Min.: 0 L/s, Max: 19.92 L/s
    -
    Flag information for hybrid vehicle

    HINT:
    *1: If no idling conditions are specified, the transmission gear selector lever should be in the N or P position, and the A/C switch and all accessory switches should be OFF.


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators, and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Put the engine in inspection mode (Click here).

  2. Connect the Techstream to the DLC3.

  3. Turn the power switch on (IG).

  4. Turn the Techstream on.

  5. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  6. Perform the Active Test by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5 and 24.8%
    1. All injectors tested at same time
    2. Perform test at less than 3000 rpm
    3. Injection volume can be changed in 1% graduations within control range
    Control the Injection Volume for A/F Sensor
    Change injection volume
    Lower by 12.5% or increase by 25%
    1. Perform test at less than 3000 rpm
    2. Control the Injection Volume for A/F Sensor enables checking and graphing of air fuel ratio sensor and heated oxygen sensor voltage outputs
    3. To conduct test, select following menu items: Active Test / Control the Injection volume for A/F sensor / A/F Control System / AFS B1S1 or AFS B2S1 and O2S B1S2 or O2S B2S2 then press the graph button on the Data List view
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the Fuel Pump/Speed
    Activate fuel pump (C/OPN Relay)
    ON/OFF
    -
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected
    2. OFF: TC and TE1 disconnected
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Control the Electric Cooling Fan
    Cooling fan control
    ON: Operate
    -
    Control the ETCS Open / Close Slow Speed
    Throttle actuator
    Open / close: Throttle valve opens or closes slowly
    Test possible when following conditions met:
    1. Power switch ON
    2. Engine is stopped
    3. Fully depressing accelerator pedal (APP: 58 degrees or more)
    Control the ETCS Open / Close Fast Speed
    Throttle actuator
    Open / close: Throttle valve opens or closes fast
    Same as above
    Control the VVT Linear (Bank 1)
    Control the VVT (bank 1 intake side)
    Between -128 and 127%
    This valve added to present oil control valve control duty
    100%: Maximum advance
    -100%: Maximum retard
    Engine stalls or idles roughly when VVT actuator operated by 100%. Test is possible while idling.
    Control the VVT System (Bank 1)
    Turn on and off oil control valve
    ON/OFF
    1. Engine stalls or idles roughly when oil control valve turned on
    2. Normal engine running or idling when oil control valve off
    Control the VVT Linear (Bank 2)
    Control the VVT (bank 2 intake side)
    Between -128% and 127%
    Same as above
    Control the VVT System (Bank 2)
    Turn on and off oil control valve
    ON/OFF
    1. Engine stalls or idles roughly when oil control valve turned on
    2. Normal engine running or idling when oil control valve off
    Activate the Vacuum Pump
    Vacuum pump
    ON/OFF
    -
    Activate the VSV for Vent Valve
    Vent valve
    ON/OFF
    -
    Activate the Fuel Filler Opener
    Fuel lid opener control
    ON: Open
    -
    Activate the Fuel Vapor-Containment Valve
    Fuel vapor-containment valve control
    ON: Open
    OFF: Close
    -
    Control the Cylinder #1 Fuel Cut
    Cylinder #1 injector fuel cut
    ON/OFF
    Test possible during vehicle stopping and engine idling
    Control the Cylinder #2 Fuel Cut
    Cylinder #2 injector fuel cut
    ON/OFF
    Control the Cylinder #3 Fuel Cut
    Cylinder #3 injector fuel cut
    ON/OFF
    Control the Cylinder #4 Fuel Cut
    Cylinder #4 injector fuel cut
    ON/OFF
    Control the Cylinder #5 Fuel Cut
    Cylinder #5 injector fuel cut
    ON/OFF
    Control the Cylinder #6 Fuel Cut
    Cylinder #6 injector fuel cut
    ON/OFF


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are set, and can detect potential malfunctions in the system. The System Check can be performed with Techstream.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the following table.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Evaporative System Check
    (Automatic Mode)
    Perform 7 steps in order to operate EVAP key-off monitor automatically
    35°C (95°F) or less
    1. If no DTCs in pending code after performing this test, system functioning normally
    2. Refer to EVAP system
    Evaporative System Check
    (Manual Mode)
    Perform 7 steps in order to operate EVAP key-off monitor automatically
    35°C (95°F) or less
    1. Used to detect malfunctioning parts
    2. Refer to EVAP system