Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

for Preparation Click here


DESCRIPTION

HINT:
This electrical throttle control system does not use a throttle cable.
The throttle position sensor is mounted on the throttle body, and detects the opening angle of the throttle valve. This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has two sensor circuits and each transmits a signal, VTA and VTA2. VTA is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM (included in the hybrid vehicle control ECU).
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.


A122559E16


DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Hybrid vehicle control ECU
P0122
Output voltage of VTA 0.2 V or less for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA circuit
  3. Open in VC circuit
  4. Hybrid vehicle control ECU
P0123
Output voltage of VTA 4.535 V or more for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA circuit
  3. Open in E2 circuit
  4. Short between VC and VTA circuits
  5. Hybrid vehicle control ECU
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Hybrid vehicle control ECU
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds
(1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. Hybrid vehicle control ECU
P0223
Output voltage of VTA2 4.8 V or more, and VTA between 0.2 V and 2.02 V, for 2 seconds (1 trip detection logic)
  1. Throttle position sensor (built into throttle body)
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. Hybrid vehicle control ECU
P2135
  1. Either condition (a) or (b) is met (1 trip detection logic):
    1. Difference between output voltages of VTA and VTA2 0.02 V or less for 0.5 seconds or more
    2. Output voltage of VTA 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA and VTA2 circuits
  2. Throttle position sensor (built into throttle body)
  3. Hybrid vehicle control ECU

HINT:
  1. When any of these DTCs are set, check the throttle valve opening angle by entering the following menus on the Techstream: Powertrain / Engine and ECT / Data List / ETCS / Throttle Sensor Position and Throttle Position No. 2.
  2. Throttle Sensor Position denotes the VTA signal (expressed in percentages), and Throttle Position No. 2 denotes the VTA2 signal (expressed in voltages).


Reference (Normal Condition):

Tester Display
Accelerator Pedal Fully Released
Accelerator Pedal Fully Depressed
Throttle Sensor Position
10 to 24%
36 to 68%
Throttle Position No. 2
2.1 to 3.1 V
4.5 to 5.0 V


MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
  1. A specific voltage difference is expected between the sensor terminals, VTA and VTA2, for each throttle valve opening angle. If the difference between VTA and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor, and sets a DTC.
  2. VTA and VTA2 each has a specific voltage range. If VTA or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor, and sets a DTC.
  3. VTA and VTA2 should never be close to the same voltage level. If VTA is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor, and sets a DTC.

MONITOR STRATEGY


Related DTCs
P0120: Throttle position sensor 1 range check (Fluctuating)
P0122: Throttle position sensor 1 range check (Low voltage)
P0123: Throttle position sensor 1 range check (High voltage)
P0220: Throttle position sensor 2 range check (Fluctuating)
P0222: Throttle position sensor 2 range check (Low voltage)
P0223: Throttle position sensor 2 range check (High voltage)
P2135: Throttle position sensor range check (Correlation)
Required Sensors/Components (Main)
Throttle position sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
2 seconds: P0120, P0122, P0123, P0220, P0222 and P0223
0.5 seconds: P2135
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None
Power switch
ON
Electronic throttle actuator power
ON

TYPICAL MALFUNCTION THRESHOLDS


P0120: 
VTA voltage
0.2 V or less, or 4.535 V or more

P0122: 
VTA voltage
0.2 V or less

P0123: 
VTA voltage
4.535 V or more

P0220: 
VTA2 voltage
1.75 V or less, or 4.8 V or more

P0222: 
Either of following conditions 1 or 2 met

1. VTA2 voltage
1.75 V or less
2. VTA2 voltage when VTA 0.2 V or more, and 2.02 V or less
4.8 V or more

P0223: 
VTA2 voltage when VTA 0.2 V or more, and 2.02 V or less
4.8 V or more

P2135: 
Either of following conditions A or B is met:
-
Condition A
-
Difference between VTA and VTA2 voltages
0.02 V or less
Condition B
-
VTA voltage
0.2 V or less
VTA2 voltage
1.75 V or less

COMPONENT OPERATING RANGE


VTA voltage
More than 0.2 V and less than 4.535 V
VTA2 voltage
More than 1.75 V and less than 4.8 V

FAIL-SAFE

When any of these DTCs, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are set, the ECM (included in the hybrid vehicle control ECU) enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

WIRING DIAGRAM


A182711E01


INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
  3. These DTCs relate to the throttle position sensor.

1.READ VALUE USING TECHSTREAM (THROTTLE POSITION NO. 1 AND THROTTLE POSITION NO. 2)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Sensor Position and Throttle Position No. 2.

  1. Check the values displayed on the Techstream.

    Result 
    When accelerator pedal released
    When accelerator pedal depressed
    Trouble Area
    Proceed to
    Throttle Sensor Position (VTA)
    Throttle Position No. 2 (VTA2)
    Throttle Sensor Position (VTA)
    Throttle Position No. 2 (VTA2)
    0%
    Between
    0 V and 0.2 V
    0%
    Between
    0 V and 0.2 V
    VC circuit open
    A
    100%
    Between
    4.5 V and 5.0 V
    100%
    Between
    4.5 V and 5.0 V
    E2 circuit open
    A
    0% or 100%
    Between
    2.1 V and 3.1 V
    (Fail-safe)
    0% or 100%
    Between
    2.1 V and 3.1 V
    (Fail-safe)
    VTA circuit open or ground short
    A
    Approx. 19%
    (Fail-safe)
    Between
    0 V and 0.2 V,
    or 4.5 V and 5.0 V
    Between
    10% and 24%
    (Fail-safe)
    Between
    0 V and 0.2 V,
    or 4.5 V and 5.0 V
    VTA2 circuit open or ground short
    A
    Between
    10% and 24%
    Between
    2.1 V and 3.1 V
    Between
    36% and 68%
    (Not fail-safe)
    Between
    4.5 V and 5.0 V
    (Not fail-safe)
    Throttle position sensor circuit normal
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)


    A110904E05
  1. Disconnect the throttle body connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B27-5 (VC) - B1-18 (VC)
    Always
    Below 1 Ω
    B27-6 (VTA) - B1-21 (VTA)
    Always
    Below 1 Ω
    B27-4 (VTA2) - B1-31 (VTA2)
    Always
    Below 1 Ω
    B27-3 (E2) - B1-28 (E2)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B27-5 (VC) or B1-18 (VC) - Body ground
    Always
    10 kΩ or higher
    B27-6 (VTA) or B1-21 (VTA) - Body ground
    Always
    10 kΩ or higher
    B27-4 (VTA2) or B1-31 (VTA2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE POSITION SENSOR - HYBRID VEHICLE CONTROL ECU)
OK


3.INSPECT HYBRID VEHICLE CONTROL ECU (VC VOLTAGE)


    A107694E16
  1. Disconnect the throttle body connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    B1-18 (VC) - B1-28 (E2)
    Power switch on (IG)
    4.5 to 5.0 V

  1. Reconnect the throttle body connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK


4.REPLACE THROTTLE BODY ASSEMBLY
  1. Replace the throttle body assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG) and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Put the engine in inspection mode (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P0120, P0122, P0123, P0220, P0223, and/or P2135
    A
    No output
    B



B
SYSTEM OK
A

REPLACE HYBRID VEHICLE CONTROL ECU (Click here)