Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0037    Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)

DTC    P0038    Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)

DTC    P0057    Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)

DTC    P0058    Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)

DTC    P0141    Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)

DTC    P0161    Oxygen Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)

for Preparation Click here


DESCRIPTION

Refer to DTC P0136 (Click here).

HINT:
  1. Sensor 2 refers to the sensor mounted behind the three-way catalytic converter and located far from the engine assembly.
  2. When any of these DTCs are set, the ECM (included in the hybrid vehicle control ECU) enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the power switch is turned off.
  3. The heated oxygen sensor heater circuit uses a relay on the B+ side of the circuit.


A179778E01


DTC No.
DTC Detection Condition
Trouble Area
P0037
P0057
Heated oxygen sensor heater current less than 0.3 A (1 trip detection logic)
  1. Open in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. IGCT relay
  4. Hybrid vehicle control ECU
P0038
P0058
Heated oxygen sensor heater current more than 2 A (1 trip detection logic)
  1. Short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. IGCT relay
  4. Hybrid vehicle control ECU
P0141
P0161
Cumulative heater resistance correction value exceeds threshold (2 trip detection logic)
  1. Open or short in heated oxygen sensor heater circuit
  2. Heated oxygen sensor heater
  3. IGCT relay
  4. Hybrid vehicle control ECU

HINT:
  1. Bank 1 refers to the bank that includes cylinder No. 1.
  2. Bank 2 refers to the bank that does not include cylinder No. 1.
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.


MONITOR DESCRIPTION

The sensing position of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM (included in the hybrid vehicle control ECU) supplements the heat from the exhaust with heat from a heating element inside the sensor.
  1. Heated oxygen sensor heater range check (P0037 and P0038):
    The ECM (included in the hybrid vehicle control ECU) monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions. If the current is below the threshold value, the ECM determines that there is an open circuit in the heater. If the current is above the threshold value, the ECM determines that there is a short circuit in the heater.
    The ECM constantly monitors the current applied to the heater. If the ECM (included in the hybrid vehicle control ECU) detects an open or short circuit, the ECM turns the MIL on and sets a DTC.
    If a malfunction is detected, the ECM cuts off the current applied to the heater.
    Example:
    The ECM sets DTC P0038 when the current in the heated oxygen sensor heater is more than 2 A. Conversely, when the heater current is less than 0.3 A, DTC P0037 is set.
  1. Heated oxygen sensor heater performance (P0141 and P0161):
    After the accumulated heater ON time exceeds 100 seconds, the ECM (included in the hybrid vehicle control ECU) calculates the heater resistance using the battery voltage and the current applied to the heater.
    If the resistance is above the threshold value, the ECM determines that there is a malfunction in the heated oxygen sensor heater and sets DTCs P0141 and P0161.

MONITOR STRATEGY


Related DTCs
P0037: Heated oxygen sensor heater (bank 1) open/short (Low electrical current)
P0038: Heated oxygen sensor heater (bank 1) open/short (High electrical current)
P0057: Heated oxygen sensor heater (bank 2) open/short (Low electrical current)
P0058: Heated oxygen sensor heater (bank 2) open/short (High electrical current)
P0141: Heated oxygen sensor heater performance (bank 1)
P0161: Heated oxygen sensor heater performance (bank 2)
Required sensors / components
Heated oxygen sensor heater (bank 1 and 2)
Required sensors / components
Vehicle speed sensor
Frequency of operation
Continuous: P0037, P0038, P0057 and P0058
Once per driving cycle: P0141 and P0161
Duration
0.5 seconds: P0037 and P0057
1 second: P0038 and P0058
10 seconds: P0141 and P0161
MIL operation
Immediate: P0037, P0038, P0057 and P0058
2 driving cycles: P0141 and P0161
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All: 
Monitor runs whenever following DTCs are not present
None

P0037 and P0057: 
Battery voltage
10.5 to 20 V

P0038 and P0058 case 1: 
Battery voltage
10.5 V or more
Engine
Running
Starter
OFF

P0038 and P0058 case 2: 
Battery voltage
10.5 to 20 V

P0141 and P0161: 
All of the following conditions are met:
-
Battery voltage
10.5 V or more
Fuel cut
OFF
Time after fuel cut ON to OFF
30 seconds or more
Accumulated heater ON time
100 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


P0037 and P0057: 
Heated oxygen sensor heater current during intrusive heating
Less than 0.3 A

P0038 and P0058 case 1: 
Heated oxygen sensor heater current
More than 2 A

P0038 and P0058 case 2: 
Hybrid IC high current limiter port
Fail

P0141 and P0161: 
Accumulated heater resistance
Varies with sensor element temperature (Example: More than 23 Ω)

COMPONENT OPERATING RANGE


Heated Oxygen (HO2) sensor heater current
0.3 A or more (when engine idles, HO2 sensor warmed up and battery voltage 11 to 14 V)

MONITOR RESULT

Refer to detailed information on Checking Monitor Status (Click here).
The test value and test limit information are described as shown in the following table. Check the monitor result and test values after performing the monitor drive pattern (refer to "Confirmation Monitor").
  1. MID (Monitor Identification Date) is assigned to each emission-related component.
  2. TID (Test Identification Date) is assigned to each emission-related component.
  3. Scaling is used to calculate the test value indicated on generic OBD II scan tools.

Heated oxygen sensor heater: 
MID
TID
Scaling
Description of Test Value
Minimum Test Limit
Maximum Test Limit
$42
$90
Multiply by 0.001 (A)
Maximum sensor heater current
Minimum test limit
Maximum test limit

WIRING DIAGRAM

Refer to DTC P0136 .

INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)


    A141063E10
  1. Disconnect the heated oxygen sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    2 (HT1B) - 1 (+B)
    20°C (68°F)
    11 to 16 Ω
    2 (HT1B) - 3 (E2)
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    1 (HT2B) - 2 (+B)
    20°C (68°F)
    11 to 16 Ω
    1 (HT2B) - 4 (E2)
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B TERMINAL OF HEATED OXYGEN SENSOR)


    A168196E06
  1. Disconnect the heated oxygen sensor connector.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Bank 1:
    Tester Connection
    Switch Condition
    Specified Condition
    P1-1 (+B) - Body ground
    Power switch on (IG)
    9 to 14 V
    Bank 2:
    Tester Connection
    Switch Condition
    Specified Condition
    B39-2 (+B) - Body ground
    Power switch on (IG)
    9 to 14 V

  1. Reconnect the heated oxygen sensor connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)


    A172443E03
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (HT1B) - D35-21 (HT1B)
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B39-1 (HT2B) - B2-33 (HT2B)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    P1-2 (HT1B) or D35-21 (HT1B) - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B39-1 (HT2B) or B2-33 (HT2B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the hybrid vehicle control ECU connectors.

  1. Reconnect the heated oxygen sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - ECM)
OK


4.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Switch the check mode using the Techstream (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 1 minute or more.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    No output
    A
    P0037, P0038, P0057, P0058, P0141 and/or P0161
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.INSPECT FUSE (EFI NO. 3 FUSE)


    A179777E02
  1. Remove the EFI No. 3 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI No. 3 fuse
    Always
    Below 1 Ω

  1. Reinstall the EFI No. 3 fuse.



NG
REPLACE FUSE (EFI NO. 3)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI NO. 3 FUSE - HEATED OXYGEN SENSOR)