DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |
DTC P0159 Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 |
|
|
| P0137 P0157 |
|
|
| P0138 P0158 |
|
|
| P0139 P0159 | Heated oxygen sensor (sensor 2) voltage does not drop to below 0.2 V immediately after fuel cut starts |
|
| Active Air Fuel Ratio Control |
| Abnormal Voltage Output of Heated Oxygen Sensor (DTC P0136 or P0156) |

| Open or Short in Heated Oxygen Sensor Circuit (DTCs P0137 and P0157 or P0138 and P0158) |

| High or Low Impedance of Heated Oxygen Sensor (DTCs P0136 and P0156 or P0137 and P0157) |
![]() |
| Abnormal Voltage Output of Heated Oxygen Sensor During Fuel-cut (DTC P0139 and P0159) |
| Related DTCs | P0136: Heated oxygen sensor output voltage (Output voltage) (bank 1) P0136: Heated oxygen sensor impedance (Low) (bank 1) P0137: Heated oxygen sensor output voltage (Low voltage) (bank 1) P0137: Heated oxygen sensor impedance (High) (bank 1) P0138: Heated oxygen sensor output voltage (High voltage) (bank 1) P0138: Heated oxygen sensor output voltage (Extremely high) (bank 1) P0139: Heated oxygen sensor output voltage during fuel cut (bank 1) P0156: Heated oxygen sensor output voltage (Output voltage) (bank 2) P0156: Heated oxygen sensor impedance (Low) (bank 2) P0157: Heated oxygen sensor output voltage (Low voltage) (bank 2) P0157: Heated oxygen sensor impedance (High) (bank 2) P0158: Heated oxygen sensor output voltage (High voltage) (bank 2) P0158: Heated oxygen sensor output voltage (Extremely high) (bank 2) P0159: Heated oxygen sensor output voltage during fuel cut (bank 2) |
| Required Sensors/Components (Main) | Heated oxygen sensor |
| Required Sensors/Components (Related) | Engine coolant temperature sensor, MAF meter, VSS, CKP sensor, throttle position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 20 seconds: Heated oxygen sensor output (Output voltage, High voltage, Low voltage) 30 seconds: Heated oxygen sensor impedance (Low) 55 seconds: Heated oxygen sensor impedance (High) 30 seconds: Heated oxygen sensor impedance (Extremely high) 6 seconds: Heated oxygen sensor voltage during fuel cut |
| MIL Operation | Immediate: Others 2 driving cycles: Heated oxygen sensor output (Output voltage, Low voltage, High voltage) |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | P0016, P0018 (VVT system bank 1, 2 - misalignment) P0031, P0032, P0051, P0052 (Air fuel ratio sensor heater - Sensor 1) P0037, P0038, P0057, P0058 (Heated oxygen sensor heater - Sensor 2) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient engine coolant temperature for Closed Loop) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301, P0302, P0303, P0304, P0305, P0306 (Misfire) P0335 (Crankshaft position sensor) P0451, P0452, P0453, P1451, P1452, P1453 (EVAP system) P2195, P2196, P2197, P2198 (Air fuel ratio sensor - rationality) P2237, P2240 Air fuel ratio sensor - open) P2238, P2241, P2252, P2255 (Air fuel ratio sensor - low impedance) P2239, P2242, P2253, P2256 (Air fuel ratio sensor - high impedance) P2A00, P2A03 (Air fuel ratio sensor - slow response) |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control begins when all of the following conditions are met | - |
| Battery voltage | 11 V or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Idle | OFF |
| Engine RPM | Less than 3200 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Close-loop |
| Fuel-cut | OFF |
| Engine load | 5 to 80% |
| Battery voltage | 11 V or more |
| Estimated heated oxygen sensor temperature | Less than 700°C (1292°F) |
| P0606 | Not set |
| Battery voltage | 11 V or more |
| Estimated heated oxygen sensor temperature | 450°C (842°F) or more |
| P0606 | Not set |
| Battery voltage | 11 V or more |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 70°C (158°F) or more |
| Catalyst temperature | 530°C (986°F) or more |
| Fuel cut | Executing |
| Either of the following conditions 1 or 2 is met | - |
| 1. All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | 0.21 to 0.59 V |
| (c) OSC (Oxygen Storage Capacity) of catalyst | 2.1 g or more |
| 2. All of the following conditions (d), (e) and (f) are met | - |
| (d) Commanded air fuel ratio | 14.9 or more |
| (e) Rear heated oxygen sensor voltage | 0.21 to 0.59 V |
| (f) OSC (Oxygen Storage Capacity) of catalyst | 2.1 g or more |
| All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | Less than 0.21 V |
| (c) OSC (Oxygen Storage Capacity) of catalyst | 2.1 g or more |
| All of the following conditions (a), (b) and (c) are met | - |
| (a) Commanded air fuel ratio | 14.9 or more |
| (b) Rear heated oxygen sensor voltage | More than 0.59 V |
| (c) OSC (Oxygen Storage Capacity) of catalyst | 2.1 g or more |
| Duration of following condition | 30 seconds or more |
| Rear HO2S impedance | Less than 5 Ω |
| Duration of following condition | 55 seconds or more |
| Rear heated oxygen sensor impedance | 15 kΩ or more |
| Duration of following condition | 10 seconds or more |
| Rear heated oxygen sensor voltage | 1.2 V or more |
| Duration until rear heated oxygen sensor voltage drops to 0.2 V after fuel cut | 6 seconds or more |
| Heated oxygen sensor voltage | Varies between 0 and 1.0 V |


| Tester Display | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio sensor) | +25% | Rich | Less than 3.1 V |
| -12.5% | Lean | More than 3.4 V | |
| O2S B1S2 or O2S B2S2 (Heated oxygen sensor) | +25% | Rich | More than 0.55 V |
| -12.5% | Lean | Less than 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() | ![]() | - |
| 2 | ![]() | ![]() |
|
| 3 | ![]() | ![]() |
|
| 4 | ![]() | ![]() |
|
| 1.READ OUTPUT DTC |
Connect the Techstream to the DLC3.
Turn the power switch on (IG) and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0138 or P0158 | A |
| P0137 or P0157 | B |
| P0136 or P0156 | C |
| P0139 or P0159 | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Put the engine in inspection mode (Click here).
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2 or O2S B2S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| HO2 Sensor Output Voltage | Proceed to |
| More than 1.0 V | A |
| Less than 1.0 V | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
![]() |
Disconnect the hybrid vehicle control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D35-21 (HT1B) - D35-19 (OX1B) | Always | 10 kΩ or higher |
| B2-33 (HT2B) - B2-26 (OX2B) | Always | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU connectors.
|
| ||||
| OK | ||
| ||
| 4.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
![]() |
Disconnect the heated oxygen sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P1-1 (+B) - P1-3 (E2) | Always | 10 kΩ or higher |
| P1-1 (+B) - P1-4 (OX1B) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B39-2 (+B) - B39-4 (E2) | Always | 10 kΩ or higher |
| B39-2 (+B) - B39-3 (OX2B) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connectors.
|
| ||||
| OK | ||
| ||
| 5.CHECK AIR FUEL RATIO SENSOR |
Connect the Techstream to the DLC3.
Turn the power switch on (IG) and turn the Techstream on.
Start the engine and warm it up with all the accessories switched off.
Drive the vehicle at 40 mph (60 km/h) or more and decelerate for 5 seconds or more. Perform this 3 times.

Enter the following menus: Powertrain / Engine and ECT / Monitor / O2 Sensor / Details.
Confirm that RANGE B1 S1 is either PASS or FAIL.
Select RANGE B1 S1 and press ENTER.
Read the test value.
| Result | Proceed to |
| OK | A |
| NG | B |
|
| ||||
|
| ||||
| 6.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR) |
Connect the Techstream to the DLC3.
Put the engine in inspection mode (Click here).
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2 or O2S B1S2.
After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.
Read the output voltage of the heated oxygen sensor when the engine rpm is suddenly increased.
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Put the engine in inspection mode (Click here).
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Injection Volume.
Change the fuel injection volume using the Techstream, monitoring the output voltage of air fuel ratio and heated oxygen sensor displayed on the Techstream.
| Tester Display (Sensor) | Voltage Variation | Proceed to |
| AFS B1S1 (Air fuel ratio sensor) AFS B2S1 (Air fuel ratio sensor) | Alternates between more and less than 3.3 V | OK |
| AFS B1S1 (Air fuel ratio sensor) AFS B2S1 (Air fuel ratio sensor) | Remains at more than 3.3 V | NG |
| AFS B1S1 (Air fuel ratio sensor) AFS B2S1 (Air fuel ratio sensor) | Remains at less than 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 8.INSPECT FOR EXHAUST GAS LEAK |
|
| ||||
| OK | |
| 9.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the heated oxygen sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (HT1B) - 1 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 2 (HT1B) - 3 (E2) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
| 1 (HT2B) - 4 (E2) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 10.INSPECT IGCT RELAY |
![]() |
Remove the IGCT relay from the engine room R/B.
Measure the resistance according to the value(s) in the table below.
| Terminal Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (When battery voltage applied to terminals 1 and 2) |
Reinstall the IGCT relay.
|
| ||||
| OK | |
| 11.CHECK TERMINAL VOLTAGE (+B TERMINAL OF HEATED OXYGEN SENSOR) |
![]() |
Disconnect the heated oxygen sensor connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| P1-1 (+B) - Body ground | Power switch on (IG) | 9 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| B39-2 (+B) - Body ground | Power switch on (IG) | 9 to 14 V |
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - HYBRID VEHICLE CONTROL ECU) |
![]() |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P1-2 (HT1B) - D35-21 (HT1B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| B39-1 (HT2B) - B2-33 (HT2B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| P1-2 (HT1B) or D35-21 (HT1B) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B39-1 (HT2B) or B2-33 (HT2B) - Body ground | Always | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU connectors.
Reconnect the heated oxygen sensor connector.
|
| ||||
| OK | |
| 13.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 14.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the Techstream to the DLC3.
Clear the DTC (Click here).
Switch the hybrid vehicle control ECU from normal mode to check mode (Click here).
Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
Deactivate the inspection mode.
Drive the vehicle at between 44 mph and 55 mph (70 km/h and 88 km/h) for at least 10 minutes\.
Drive the vehicle at 44 mph (70 km/h) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.
Turn the Techstream on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0136, P0137, P0138, P0156, P0157 and P0158.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is Incomplete, perform the driving pattern increasing the vehicle speed and using the B position to decelerate the vehicle.

| Display (DTC Output) | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0136, P0137, P0138, P0156, P0157 or P0158 is output) | B |
|
| ||||
| A | ||
| ||
| 15.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 16.PERFORM CONFIRMATION DRIVING PATTERN |
|
| ||||
| OK | ||
| ||
| 17.INSPECT FUSE (EFI NO. 3 FUSE) |
![]() |
Remove the EFI No. 3 fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI No. 3 fuse | Always | Below 1 Ω |
Reinstall the EFI No. 3 fuse.
|
| ||||
| OK | ||
| ||
| 18.READ VALUE USING TECHSTREAM |
Connect the Techstream to the DLC3.
Put the engine in inspection mode (Click here).
Start the engine.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2 or O2S B2S2.
Allow the engine to idle.
Read the heated oxygen sensor output voltage while idling.
| HO2 Sensor Output Voltage | Proceed to |
| More than 1.0 V | A |
| Less than 1.0 V | B |
|
| ||||
| OK | |
| 19.INSPECT OXYGEN SENSOR |
![]() |
Disconnect the heated oxygen sensor connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| P1-1 (+B) - P1-3 (E2) | Always | 10 kΩ or higher |
| P1-1 (+B) - P1-4 (OX1B) | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| B39-2 (+B) - B39-4 (E2) | Always | 10 kΩ or higher |
| B39-2 (+B) - B39-3 (OX2B) | Always | 10 kΩ or higher |
Reconnect the heated oxygen sensor connectors.
|
| ||||
| OK | |
| 20.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the hybrid vehicle control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D35-21 (HT1B) - D35-19 (OX1B) | Always | 10 kΩ or higher |
| B2-33 (HT2B) - B2-26 (OX2B) | Always | 10 kΩ or higher |
Reconnect the hybrid vehicle control ECU connectors.
|
| ||||
| OK | ||
| ||
| 21.READ VALUE USING TECHSTREAM (DTC P0139 OR P0159 IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Clear the DTC (Click here).
Switch the hybrid vehicle control ECU from normal mode to check mode (Click here).
Warm-up the engine until the engine coolant temperature is 75°C (167°F) or more.
Deactivate the inspection mode.
Drive the vehicle at between 44 mph and 55 mph (70 km/h and 88 km/h) for at least 10 minutes\.
Drive the vehicle at 44 mph (70 km/h) or more and decelerate the vehicle for 5 seconds or more. Perform this 3 times.
Turn the Techstream on.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTCs: P0139 and P0159.
Check that DTC MONITOR is NORMAL. If DTC MONITOR is Incomplete, perform the driving pattern increasing the vehicle speed and using the B position to decelerate the vehicle.

| Display (DTC Output) | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0139 or P0159 is output) | B |
|
| ||||
| A | ||
| ||