Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0116    Engine Coolant Temperature Circuit Range / Performance Problem

for Preparation Click here


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor, of which the resistance value varies according to the engine coolant temperature.
The structure of the sensor and its connection to the ECM (included in the hybrid vehicle control ECU) are similar to the intake air temperature sensor.

DTC No.
DTC Detection Condition
Trouble Area
P0116
When either of following conditions is met (2 trip detection logic):
  1. When cold engine is started and engine is warmed up, engine coolant temperature sensor value does not change.
  2. After engine is warmed up, engine coolant temperature sensor value does not change when engine stopped and then next cold engine start is performed.
  1. Thermostat
  2. Engine coolant temperature sensor

MONITOR DESCRIPTION

  1. Engine coolant temperature sensor cold start monitor
    When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is set.
  1. Engine coolant temperature sensor soak monitor
    After a warmed up engine is started, if the engine coolant temperature sensor value does not change when the engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is set.

MONITOR STRATEGY


Related DTCs
P0116: Engine coolant temperature sensor cold start monitor
P0116: Engine coolant temperature sensor soak monitor
Required Sensors/Components (Main)
Engine coolant temperature sensor
Required Sensors/Components (Related)
None
Frequency of Operation
Once per driving cycle
Duration
5 hours or more
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Engine coolant temperature sensor cold start monitor: 
Monitor runs whenever following DTCs are not present
None
Battery voltage
10.5 V or more
Time after engine start
1 second or more
Engine coolant temperature at engine start
Less than 60°C (140°F)
Intake air temperature sensor circuit
OK
Soak time
0 seconds or more
Accumulated mass air flow
1397 g or more
Engine
Running
Fuel cut
OFF
Difference between engine coolant temperature at engine start and intake air temperature
Less than 40°C (72°F)

Engine coolant temperature sensor soak monitor: 
Monitor runs whenever following DTCs are not present
P0100 to P0103: MAF meter
P0110 to P0113: Intake air temperature sensor
Battery voltage
10.5 V or more
Engine
Running
Soak time
5 hours or more
Either of the following conditions (a) or (b) is met
-
(a) Engine coolant temperature
60°C (140°F) or more
(b) Accumulated MAF
2921 g or more

TYPICAL MALFUNCTION THRESHOLDS


Engine coolant temperature sensor cold start monitor: 
Engine coolant temperature sensor value change
Less than 5°C (9°F)

Engine coolant temperature sensor soak monitor: 
Difference between current engine coolant temperature sensor value and previous engine coolant temperature sensor value when engine stopped
Less than 5°C (9°F)

COMPONENT OPERATING RANGE


Engine coolant temperature
Engine coolant temperature sensor value changes in accordance with actual engine coolant temperature

INSPECTION PROCEDURE

HINT:
  1. If any of DTCs P0115, P0117, P0118 or P0125 are set simultaneously with DTC P0116, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Display (DTC output)
    Proceed to
    P0116
    A
    P0116 and other DTCs
    B

    HINT:
    If any DTCs other than P0116 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2.INSPECT THERMOSTAT
  1. Remove the thermostat (Click here).

  1. Check the valve opening temperature of the thermostat.

    Standard:
    80 to 84°C (176 to 183°F)

    HINT:
    In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.

  1. Reinstall the thermostat (Click here).



NG
REPLACE THERMOSTAT
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)